CENTURY SERIES

VX

AUX SENDS 1- 8 Individual Level Controls

These Push-On/Push Off pots adjust signal level sent to respective Aux buses. Pushing the switch down turns the send on or off. An associated two color LED indicates status: OFF indicates an 'off' state; GREEN indicates the Aux send is on, and not muted; RED indicates the Aux send is on, but muted. The signal source for these mixes may be selected (by Aux bus) to be pre or post fader by the GLOBAL switches located in the Vx Master section.

Aux 8 DIR OUT Switch w/LED

Removes the Aux 8 signal from the Aux 8 bus, and assigns the signal to the direct out 1/4" connector on the rear panel, instead of the normal post fader Dir Out signal.

AUX 8 PRE Switch w/LED

Switches the Aux 8 signal source between pre and post-fader.

PAN CONTROL

Positions the channel image between left and right or between left-center-right; operates with groups when pan switch is selected. (See L-C-R Switch).

In LCR mode, continuous variation is available between full level to left only (pan full counter-clockwise position) full level to right only (pan full clockwise) and center position (full level to mono/center, no output to left or right).

MUTE Switch w/LED

Turns off the channel audio to outputs. LED on = audio off. Both pre and post fader audio is muted. When pre-fader sends should not mute refer to USER OPTIONS. MUTE responds to the local switch, the Mute Groups, and VCA Group Mute (internal user option).

MONO Bus Assign Switch

Assigns the input signal to the Center / Mono bus. If L-C-R is selected then PAN adjustment will be effective.

L-C-R Switch

Changes the PAN function from normal L-R to L-C-R opera- tion. The mix to the L,R & Mono buses is adjustable with L-C- R PAN. Refer to Special facilities for more information.

PAN Switch / Group Assign Switches (1-8) w/LED's

Group assign switches route the post-fader signal to the Group buses. PAN does not adjust these outputs unless the PAN switch is selected. Then the L & R sides of the control corre- spond to Odd and Even Group bus numbers.

SOLO Switch w/LED

Operator monitor facility, switches channel audio into the headphones and Solo Meters. Choice of PFL or AFL is made in the center master section. AFL is after fader, after Pan pot, and after mute.

5-Segment LED Array

Dedicated channel level meter connected pre-fader, post EQ (post fader option, refer to User Options). Top red Peak LED responds to audio levels pre EQ, post EQ and post-fader. Normal indication is green on, red flashing only on loud peaks.

Fader

100mm linear VCA level control, adjusts the level to all 'POST' fader outputs, ie auxiliaries 1-8 selected post, AFL, Group assigns 1-8, L, R & Mono output mixes. Local fader movements combine with movements of any VCA Group faders the channel is assigned to. The change in audio level is the sum of the two. If the Group fader is closed no local move- ments will be heard. If the Group is at -5, local fader settings will be reduced 5dB. Refer also to Expansion and muting.

VCA Group 1-8 selectors

Assign the channel to the VCA group control buses. Puts the channel audio level under the (remote) control of the VCA Group fader along with other channels assigned to the same group. Independant of the Group Audio Assign section above.

VCA LED

Indicates VCA gain (i.e., gain of fader stage) via a two-color LED. Indications are as follows: Green - intensity indicates gain status (gain of fader stage). Red - indicates maximum VCA gain has been reached, approximately 15dB. When the gain LED is red then further requests for increased level, by moving the channel fader or the VCA Group fader up, will produce no response.

Mute Group selectors A-D

Assign input channels to any of the four Scene Mute groups. Mute response occurs only when the group Master has been activated.

Mute Groups Safe Switch w/LED

Bypasses the selected Scene Mute assignments. No Scene Mutes can occur. An associated green LED indicates the chan- nel is in a SAFE (isolated) state.

PAGE 13

Page 15
Image 15
Peavey Century Series owner manual PAN Control, Vca Led