FX82052 Rear PANEL, -4 Models | Pelco specs

FX82052 REAR PANEL, -4 MODELS

Figure 5 illustrates the rear panel of the FX82052 module containing five 10BASE-T/100BASE-TX ports and two 100BASE-FX fiber ports that each accept two fibers (-4 models).

Figure 5. Rear Panel of FX82052 Module, -4 Models (SC Fiber Connectors Shown)

ìRack Power/Alarm Connector: 4-pin connector for power/alarm connection of rack- mounted module

îStand-Alone Power Connector: 2-pin connector for power connection of stand-alone module; removable mating connector with screw terminals (not shown)

ï10BASE-T/100BASE-TX Ports 1-5: RJ-45 connectors

ñFiber Optic Ports A and B: Dual-fiber ST or SC connectors (dependent on FX82052 model)

óRJ-45 10BASE-T/100BASE-TX Port Status LED, Left: Link/activity status indicator

rRJ-45 10BASE-T/100BASE-TX Port Status LED, Right: Duplex mode/collision indicator

For additional information about rear-panel connections, refer to Connections on page 20. For detailed information about the RJ-45 LEDs, refer to Troubleshooting on page 26.

C2607M (2/07)

13

Image 13

Pelco manual FX82052 Rear PANEL, -4 Models, 10BASE-T/100BASE-TX Ports 1-5 RJ-45 connectors

Contents

Ethernet Switch List of Illustrations Contents List of Tables TX Mode Switch Settings FX Mode Switch Settings Important Safety Instructions Risk of Electric Shock Do not Open Radio and Television Interference Regulatory Notices Description Product Overview POINT-TO-POINT Application with Fiber Redundancy C2607M 2/07 FX82052, -2 Models Multimode Models ModelsSingle-Mode Models† FX82052, -4 Models Multimode Models Front Panel Power LED Pelco badge100BASE-FX Status LED Per fiber port a and B Rear Panel 10BASE-T/100BASE-TX Ports 1-5,RJ-45 connectors FX82052 Rear PANEL, -4 Models 10BASE-T/100BASE-TX Ports 1-5 RJ-45 connectors Package Contents Installation Flow control is disabled by default Autonegotiation is enabled by default Table A. TX Mode Switch Settings Setting Fiber Failover ModeFlow control default setting 10BASE-T/100BASE-TX Modes of Operation Mode of Operation Table B. FX Mode Switch SettingsDefault setting Secondary fiber link Mounting the FX82052 Module Into a Rack Mounting Mounting the FX82052 Module Using the Wall Clip Connections FX82052 Connections, -4 Models SC Fiber Connectors Shown Fiber connections 10BASE-T/100BASE-TX connections Fiber Link FX Mode Position Fiber Ports a and B Are Independent FX Mode Position FX Mode Position Fiber Ports a and B Are Independent Check power connection TroubleshootingModule Reseat module or power Supply as necessary Replace power supply Meaning Optic Fault LED on local Section in this table Indication Fefi On local module Optical signalReplace local module By the remote link Meaning Possible Cause Corrective Action Optic Fault LED Desired, refer to Setting Table D. Troubleshooting with Rear-Panel IndicatorsAmber If 10BASE-T operation is Meaning Possible Cause Corrective Action Duplex mode Duplex link Duplex modeRefer to Setting If half-duplex mode is Green Port is set to If 100BASE-TX full-duplex Mode refer to SettingFull-duplex operation is not Flashing green Port is set to Normal or excessive Table D. Troubleshooting with Rear-Panel Indicators Optic Fault optic signal/laser status per fiber port SpecificationsLink/activity and speed, duplex/collision and speed Multimode 62.5/125 μm FX82052, -2 Models Wavelength Optical MaximumSingle-Mode 9/125 μm FX82052SSTR-2 Fibers Illustrates RJ-45 MDI/MDI-X connector pinouts Appendix. RJ-45 Connector Pinouts Product Warranty and Return Information ISO9001