Specifications | Pelco FX82052 manual

Specifications

PERFORMANCE
Switch Type	Unmanaged Layer 2
Switch Method	Store and forward
Switch Fabric	Non-head-of-line blocking
Data Rate	10/100 Mbps
Compliance	IEEE 802.3, 802.3u, 802.3x
Interface	Auto MDI/MDI-X
Operating Mode	Half-duplex or full-duplex
Address Table Size	1,024 MAC address entries with automatic learning and aging
Quality of Service	IEEE 802.1p priority, tag-based, 4 queues per port,
	weighted fair queuing scheduling
Maximum Frame Size	Untagged Ethernet frames up to 1,518 bytes
	Tagged Ethernet frames up to 1,522 bytes
GENERAL
Operating Temperature	-40° to 167°F (-40° to 75°C)
Input Power Requirements	12 VDC or 24 VAC, 0.50 A
LED Indicators	Power
	Fiber Redundancy Mode Status
	100BASE-FX Port Status (link/activity, FEFI per fiber port)
	Optic Fault (optic signal/laser status per fiber port)
	10BASE-T/100BASE-TX Port Status (2 LEDs per port:
	link/activity and speed, duplex/collision and speed)
Dimensions	8.75" D x 2.28" W x 4.81" H
	(22.23 x 5.79 x 12.22 cm)
Unit Weight	2.4 lb (1.09 kg)
MECHANICAL
Connectors
Rack Power/Alarm	1, 4-pin connector
Stand-Alone Power	1, 2-pin connector, screw terminal
Electrical	5, RJ-45, 10BASE-T/100BASE-TX
Fiber Optic	2, single-fiber ST or SC (-2 models)
	2, dual-fiber ST or SC (-4 models)

C2607M (2/07)

35

Image 35

Pelco FX82052 manual Specifications, Optic Fault optic signal/laser status per fiber port

Contents

Ethernet Switch List of Illustrations Contents List of Tables TX Mode Switch Settings FX Mode Switch Settings Important Safety Instructions Risk of Electric Shock Do not Open Radio and Television Interference Regulatory Notices Description Product Overview POINT-TO-POINT Application with Fiber Redundancy C2607M 2/07 FX82052, -4 Models Multimode Models ModelsFX82052, -2 Models Multimode Models Single-Mode Models† 100BASE-FX Status LED Per fiber port a and B Power LED Pelco badgeFront Panel Rear Panel 10BASE-T/100BASE-TX Ports 1-5,RJ-45 connectors FX82052 Rear PANEL, -4 Models 10BASE-T/100BASE-TX Ports 1-5 RJ-45 connectors Package Contents Installation Flow control is disabled by default Autonegotiation is enabled by default 10BASE-T/100BASE-TX Modes of Operation Setting Fiber Failover ModeTable A. TX Mode Switch Settings Flow control default setting Secondary fiber link Table B. FX Mode Switch SettingsMode of Operation Default setting Mounting the FX82052 Module Into a Rack Mounting Mounting the FX82052 Module Using the Wall Clip Connections FX82052 Connections, -4 Models SC Fiber Connectors Shown Fiber connections 10BASE-T/100BASE-TX connections Fiber Link FX Mode Position Fiber Ports a and B Are Independent FX Mode Position FX Mode Position Fiber Ports a and B Are Independent Replace power supply TroubleshootingCheck power connection Module Reseat module or power Supply as necessary Meaning By the remote link Indication Fefi On local module Optical signalOptic Fault LED on local Section in this table Replace local module Meaning Possible Cause Corrective Action Optic Fault LED If 10BASE-T operation is Table D. Troubleshooting with Rear-Panel IndicatorsDesired, refer to Setting Amber Meaning Possible Cause Corrective Action If half-duplex mode is Duplex modeDuplex mode Duplex link Refer to Setting Flashing green Port is set to Normal or excessive Mode refer to SettingGreen Port is set to If 100BASE-TX full-duplex Full-duplex operation is not Table D. Troubleshooting with Rear-Panel Indicators Link/activity and speed, duplex/collision and speed SpecificationsOptic Fault optic signal/laser status per fiber port FX82052SSTR-2 FX82052, -2 Models Wavelength Optical MaximumMultimode 62.5/125 μm Single-Mode 9/125 μm Fibers Illustrates RJ-45 MDI/MDI-X connector pinouts Appendix. RJ-45 Connector Pinouts Product Warranty and Return Information ISO9001