POINT-TO-POINT Application with Fiber Redundancy | Pelco FX82052

FIVE 10/100 Mbps	ONE	FIVE 10/100 Mbps
CONNECTIONS	FIBER	CONNECTIONS
	(PRIMARY)
FX82052-2		FX82052-2

ONE

FIBER

(REDUNDANT)

POINT-TO-POINT APPLICATION WITH FIBER REDUNDANCY

FX82052-2		FX82052-2		FX82052-2		FX82052-2
	ONE		ONE		ONE
	FIBER		FIBER		FIBER

FIVE 10/100 Mbps	FIVE 10/100 Mbps	FIVE 10/100 Mbps	FIVE 10/100 Mbps
CONNECTIONS	CONNECTIONS	CONNECTIONS	CONNECTIONS

SAMPLE DROP-AND-REPEAT APPLICATION

Figure 1. Point-to-Point and Drop-and-Repeat Applications (One Fiber per Fiber Port)

	FIVE 10/100 Mbps		TWO	FIVE 10/100 Mbps
	FIVE 10/100 Mbps		FIBERS	FIVE 10/100 Mbps
	CONNECTIONS		FIBERS		CONNECTIONS
	CONNECTIONS		(PRIMARY)		CONNECTIONS
			(PRIMARY)

		FX82052-4		FX82052-4

TWO

FIBERS

(REDUNDANT)

POINT-TO-POINT APPLICATION WITH FIBER REDUNDANCY

FX82052-4	FX82052-4	FX82052-4	FX82052-4
TWO		TWO	TWO
FIBERS		FIBERS	FIBERS
FIVE 10/100 Mbps	FIVE 10/100 Mbps	FIVE 10/100 Mbps	FIVE 10/100 Mbps
CONNECTIONS	CONNECTIONS	CONNECTIONS	CONNECTIONS

SAMPLE DROP-AND-REPEAT APPLICATION

Figure 2. Point-to-Point and Drop-and-Repeat Applications (Two Fibers per Fiber Port)

8	C2607M (2/07)

Image 8

Pelco FX82052 manual POINT-TO-POINT Application with Fiber Redundancy

Contents

Ethernet Switch Contents List of Illustrations TX Mode Switch Settings FX Mode Switch Settings List of Tables Important Safety Instructions Risk of Electric Shock Do not Open Regulatory Notices Radio and Television Interference Product Overview Description POINT-TO-POINT Application with Fiber Redundancy C2607M 2/07 Models FX82052, -2 Models Multimode ModelsSingle-Mode Models† FX82052, -4 Models Multimode Models 100BASE-FX Status LED Per fiber port a and B Power LED Pelco badgeFront Panel 10BASE-T/100BASE-TX Ports 1-5,RJ-45 connectors Rear Panel 10BASE-T/100BASE-TX Ports 1-5 RJ-45 connectors FX82052 Rear PANEL, -4 Models Installation Package Contents Autonegotiation is enabled by default Flow control is disabled by default Setting Fiber Failover Mode Table A. TX Mode Switch SettingsFlow control default setting 10BASE-T/100BASE-TX Modes of Operation Table B. FX Mode Switch Settings Mode of OperationDefault setting Secondary fiber link Mounting Mounting the FX82052 Module Into a Rack Mounting the FX82052 Module Using the Wall Clip FX82052 Connections, -4 Models SC Fiber Connectors Shown Connections 10BASE-T/100BASE-TX connections Fiber connections Fiber Link FX Mode Position Fiber Ports a and B Are Independent FX Mode Position FX Mode Position Fiber Ports a and B Are Independent Troubleshooting Check power connectionModule Reseat module or power Supply as necessary Replace power supply Meaning Indication Fefi On local module Optical signal Optic Fault LED on local Section in this tableReplace local module By the remote link Meaning Possible Cause Corrective Action Optic Fault LED Table D. Troubleshooting with Rear-Panel Indicators Desired, refer to SettingAmber If 10BASE-T operation is Meaning Possible Cause Corrective Action Duplex mode Duplex mode Duplex linkRefer to Setting If half-duplex mode is Mode refer to Setting Green Port is set to If 100BASE-TX full-duplexFull-duplex operation is not Flashing green Port is set to Normal or excessive Table D. Troubleshooting with Rear-Panel Indicators Link/activity and speed, duplex/collision and speed SpecificationsOptic Fault optic signal/laser status per fiber port FX82052, -2 Models Wavelength Optical Maximum Multimode 62.5/125 μmSingle-Mode 9/125 μm FX82052SSTR-2 Fibers Appendix. RJ-45 Connector Pinouts Illustrates RJ-45 MDI/MDI-X connector pinouts Product Warranty and Return Information ISO9001