Connections | Pelco FX82052 manual

CONNECTIONS

Connections to the FX82052 module are made on the rear panel of the module. Refer to Figure 9 and to Figure 10 for illustrations of connections to FX82052, -2 models and FX82052, -4 models, respectively.

POWER/ALARM

CONNECTION FOR

RACK-MOUNTED MODULE

POWER CONNECTION FOR

STAND-ALONE MODULE

10/100 NETWORK CABLE

10/100 NETWORK CABLE

10/100 NETWORK CABLE

10/100 NETWORK CABLE

10/100 NETWORK CABLE

FIBER OPTIC CABLE TO PORT B (CONNECTS TO PORT A ON REMOTE MODULE)

FIBER OPTIC CABLE TO PORT A (CONNECTS TO PORT B ON REMOTE MODULE)

Figure 9. FX82052 Connections, -2 Models (SC Fiber Connectors Shown)

POWER/ALARM

CONNECTION FOR

RACK-MOUNTED MODULE

POWER CONNECTION FOR

STAND-ALONE MODULE

10/100 NETWORK CABLE

10/100 NETWORK CABLE

10/100 NETWORK CABLE

10/100 NETWORK CABLE

10/100 NETWORK CABLE

FIBER OPTIC CABLES

FIBER OPTIC CABLES

Figure 10. FX82052 Connections, -4 Models (SC Fiber Connectors Shown)

20	C2607M (2/07)

Image 20

Pelco manual FX82052 Connections, -4 Models SC Fiber Connectors Shown

Contents

Ethernet Switch Contents List of Illustrations TX Mode Switch Settings FX Mode Switch Settings List of Tables Important Safety Instructions Risk of Electric Shock Do not Open Regulatory Notices Radio and Television Interference Product Overview Description POINT-TO-POINT Application with Fiber Redundancy C2607M 2/07 Models FX82052, -2 Models Multimode ModelsSingle-Mode Models† FX82052, -4 Models Multimode Models 100BASE-FX Status LED Per fiber port a and B Power LED Pelco badgeFront Panel 10BASE-T/100BASE-TX Ports 1-5,RJ-45 connectors Rear Panel 10BASE-T/100BASE-TX Ports 1-5 RJ-45 connectors FX82052 Rear PANEL, -4 Models Installation Package Contents Autonegotiation is enabled by default Flow control is disabled by default Setting Fiber Failover Mode Table A. TX Mode Switch SettingsFlow control default setting 10BASE-T/100BASE-TX Modes of Operation Table B. FX Mode Switch Settings Mode of OperationDefault setting Secondary fiber link Mounting Mounting the FX82052 Module Into a Rack Mounting the FX82052 Module Using the Wall Clip FX82052 Connections, -4 Models SC Fiber Connectors Shown Connections 10BASE-T/100BASE-TX connections Fiber connections Fiber Link FX Mode Position Fiber Ports a and B Are Independent FX Mode Position FX Mode Position Fiber Ports a and B Are Independent Troubleshooting Check power connectionModule Reseat module or power Supply as necessary Replace power supply Meaning Indication Fefi On local module Optical signal Optic Fault LED on local Section in this tableReplace local module By the remote link Meaning Possible Cause Corrective Action Optic Fault LED Table D. Troubleshooting with Rear-Panel Indicators Desired, refer to SettingAmber If 10BASE-T operation is Meaning Possible Cause Corrective Action Duplex mode Duplex mode Duplex linkRefer to Setting If half-duplex mode is Mode refer to Setting Green Port is set to If 100BASE-TX full-duplexFull-duplex operation is not Flashing green Port is set to Normal or excessive Table D. Troubleshooting with Rear-Panel Indicators Link/activity and speed, duplex/collision and speed SpecificationsOptic Fault optic signal/laser status per fiber port FX82052, -2 Models Wavelength Optical Maximum Multimode 62.5/125 μmSingle-Mode 9/125 μm FX82052SSTR-2 Fibers Appendix. RJ-45 Connector Pinouts Illustrates RJ-45 MDI/MDI-X connector pinouts Product Warranty and Return Information ISO9001