Antenna Connector, External Speaker Jack | Furuno FM-3000 instruction

eANTENNA CONNECTOR

Connects a marine VHF antenna with a PL-259 connec- tor.

RCAUTION

Transmitting without an antenna may damage the transceiver.

rNMEA IN (Red)/NMEA OUT (White) JACKS

Connects to a GPS receiver for position and time indica- tions.

•An NMEA0183 ver. 2.0 or 3.01 (sentence formatters RMC, GGA, GNS, GLL) compatible GPS receiver is required. Ask your dealer about suitable GPS receivers.

RCA

NMEA IN (+) NMEA IN (–)

Connects to a PC or navigation equipment (NMEA0183 ver. 3.01 sentence formatters DSC, DSE compatible) for plotting received other ships position data.

RCA

NMEA OUT (+) NMEA OUT (–)

8.Connections and Maintenance

tEXTERNAL SPEAKER JACK

➥Connects to an external speaker.

RCAUTION

After connecting the DC power cable, NMEA IN/OUT jacks and external speaker jack cover the connector and jacks with a rubber vulcanising tape as shown below, to prevent water seeping into the transceiver.

Rubber vulcanizing tape

Page 51

Image 51

Furuno FM-3000 manual Antenna Connector, Nmea in Red/NMEA OUT White Jacks, External Speaker Jack

Contents

Marine VHF Radiotelephone FM-3000 Foreword Case of Emergency Do not open the equipment Do not disassemble or modify the equipmentAny repair work must be done by a licensed radio technician Transceiver Only qualified personal should work in- side the equipmentStandard Steerling Compass Table of Contents Panel Description Setting Tag ChannelsSet Mode Programming Installation Vii System Conﬁgulation Standard supply & Options Standard supplyOptions HI/LO key ControlsFront Panel SQL control p CH/WX DW U/I/C key LO/DX IC SCR key16 9 key Distress key Function Display Microphone Channel 9 Call channel Basic OperationChannel Selection Channel Rotate Channel to select a channel Push once When Weather alert is OFF A. channels Or twiceWeather channels Change the channel group, if necessary Receiving and Transmitting Push HI/LO to select the output power, if necessary Call Channel Programming Channel CommentsPush Programming scrambler codes Set mode Scrambler code itemOptional Voice Scrambler Operation Activating the Scrambler Again Example Operating Tri-watch on INT Channel Dualwatch/Tri-WatchDescription Operation Scan Types Scan Operation Scan starts Setting Tag ChannelsConvinient Clearing setting all tagged channels Starting a Scan Programming Address ID/Group ID DSC OperationMmsi Code Programming DSC Individual ID Deleting Address ID/Group ID Set the individual ID and ID nameRotate Channel to select the desired ID name for deleting Push DSC/ENT to set the time, and exit the DSC menu Edit the digit of your latitude data by using ChannelEdit the digit of your longitude data by using Channel Edit the digit of the current UTC time by using CHAN- NEL Sentence formatteres ‘GGA,’ ‘GNS,’ ‘GLL’ Position/Time Indication Distress alert contains default Distress CallSimple call Normal call Push Distress for 5 sec. to transmit the Distress call Transmitting DSC Calls Transmitting Individual callPush DSC/ENT to transmit the Individual call Transmitting Individual acknowledgement Indv ACK Push DSC/ENT to transmit the Group call Transmitting Group call Push DSC/ENT to transmit the All Ships call Transmitting All Ships call Push DSC/ENT to transmit the Position Request call Transmitting Position Request call Transmitting Position Report call Transmitting Position Reply call Transmitting Position Report Reply callPush DSC/ENT to transmit the Position Report call Receiving an Individual call Receiving DSC CallsReceiving a Distress call Receiving a Distress acknowledgement Receiving an All Ships call Receiving a Distress Relay callReceiving a Geographical Area call Receiving a Position Report Reply call Receiving a Position Request callReceiving a Position Report call Receiving a Position Reply call Rotate Channel to scroll the message Received MessagesDistress message Rotate Channel to select Distress, push DSC/ENT Rotate Channel to select Other, push DSC/ENT Other messages Push DSC/ENT to program and to exit the DSC menu DSC Set ModeOffset time Rotate Channel to select Offset time, push DSC/ENT Push DSC/ENT to exit the DSC menu Mmsi code checkRotate Channel to select Mmsi Check, push DSC/ENT Check the 9-digit Mmsi DSC self ID code FM-3000 caller Push LO/DX IC SCR for 1 sec. to enter Intercom modeOther Functions Intercom Operation Display Backlighting Microphone Lock Function Set Mode Set Mode ProgrammingAuto ACK items are not selectable when using FM-3010 Weather alert Set Mode ItemsScan mode Scan resume timer Internal speaker This item adjusts the contrast of the LCD in 8 stepsDSC watch Beep tone Attenuation level Scrambler codeAutomatic acknowledgement Antenna Connections Connections and MaintenanceFuse Replacement Cleaning Antenna Connector Nmea in Red/NMEA OUT White JacksExternal Speaker Jack Mounting the Transceiver Using the supplied mounting bracket Attach the clamps on either side of the FM-3000 Using the optional FM-3040 Optional Unit Installation Dimensions 145.0 5 23⁄32 103.0 110.0 4 11⁄32 165.0 6 1⁄253.0 ⁄32 Unit mm Problem Possible Cause Solution Troubleshooting Channel List † Low power only Radio license for boaters U.S.A. only Operating Rules Transmitter SpeciﬁcationsSpeciﬁcations General Channel UP/DOWN Keys Y/Z PTT Switch PTT pgsPanel Description Front and side keys SQUELCH/MONITOR/LOCK KEY SQL Moni L VOLUME/DIMMER KEY VOL DIMCHANNEL/DUALWATCH/TRI-WATCH KEY CH/WX DW U/I/C LO/DX IC SCR Top keys 1DUAL/TRI Watch Indicator pgs Volume Indicator pSquelch Indicator p Scan Indicator pgs A. channels Call channel13.3 3 Weather channels Channel group Turn power on Set output Push H/L to select the output power, if necessaryPush Y/Z to select the desired channel Activating the All key lock function Push Y/Z to adjust the backlight levelLock Functions Activating the Lock function Push CH/WX DW U/I/C several Monitor FunctionRF Attenuator Function Push LO/DX to turn the RF Attenuator function on and OFF LO/DX IC SCR to turn Dualwatch/Tri-watch OperationProgramming scramble codes Push Y/Z to select the desired channel To cancel the tag channel setting, push Scan TAG for 1 sec Convenient Clearing setting all tagged channelsTo stop the scan, push Scan TAG Entering Set mode Turn power OFF While pushing 16 9 , turn power onBeep tone Beep Intercom beep function Push SQL to move to forward then push Y/Z to seAvailable characters 13.17 FM-3010 supplied accessories Accessories included with the FM-3010 QtyConnection cable FM-3011 6 m 20 ft Completed installation should look like this Installation Mm 3⁄32˝ R11 Mm 3⁄32 165 mm 61⁄2 149 mm 57⁄8