Speciﬁcations, General, Transmitter, Receiver | Furuno FM-3000

12. Speciﬁcations

■Speciﬁcations

General

• Frequency coverage	:
Transmit		156.025–157.425 MHz
Receive		156.050–163.275 MHz
• Mode	: FM (16K0G3E)
		DSC (16K0G2B)
• Channel spacing	:	25 kHz
• Current drain (at 13.8 V)	: TX high		5.5 A max.
		Max. audio	1.5 A max.
• Power supply requirement:		13.8 V DC ±15%
• Frequency stability	: ±10 ppm
		(–20°C to +60°C; –4°F to +140°F)
• Dimensions	: 165(W) ⋅ 110(H) ⋅ 103(D) mm
(Projection not included)		6 1⁄2(W) ⋅ 4 11⁄32(H) ⋅ 4 1⁄16(D) in
• Weight (approx.)	:	1130 g; 2 lb 8 oz

All stated specifications are subject to change without notice or obligation.

Transmitter

• Output power	: 25 W / 1 W
• Modulation system	: Variable reactance phase
	modulation
• Max. frequency deviation	: ±5.0 kHz
• Spurious emissions	: –70 dBc

Receiver

• Receive system	: Double conversion
	superheterodyne
• Sensitivity (12 dB SINAD) : 0.22 µV (typical)
• Squelch sensitivity	: 0.22 µV (typical)
• Intermodulation rejection ratio: More than 75 dB
• Spurious response	: More than 75 dB
rejection ratio
• Adjacent channel selectivity : More than 75 dB
• Audio output power	: 4.5 W (typical) at 10% distortion
	with a 4 Ω load

50

Image 59

Furuno FM-3000 manual Speciﬁcations, General, Transmitter, Receiver

Contents

Marine VHF Radiotelephone FM-3000 Foreword Case of Emergency Any repair work must be done by a licensed radio technician Do not open the equipmentDo not disassemble or modify the equipment Transceiver Only qualified personal should work in- side the equipmentStandard Steerling Compass Table of Contents Panel Description Setting Tag ChannelsSet Mode Programming Installation Vii System Conﬁgulation Options Standard supply & OptionsStandard supply HI/LO key ControlsFront Panel SQL control p CH/WX DW U/I/C key LO/DX IC SCR key16 9 key Distress key Function Display Microphone Channel 9 Call channel Basic OperationChannel Selection Channel Rotate Channel to select a channel Push once When Weather alert is OFF A. channels Or twiceWeather channels Change the channel group, if necessary Receiving and Transmitting Push HI/LO to select the output power, if necessary Push Call Channel ProgrammingChannel Comments Programming scrambler codes Set mode Scrambler code itemOptional Voice Scrambler Operation Activating the Scrambler Again Example Operating Tri-watch on INT Channel Dualwatch/Tri-WatchDescription Operation Scan Types Scan Operation Scan starts Setting Tag ChannelsConvinient Clearing setting all tagged channels Starting a Scan Programming Address ID/Group ID DSC OperationMmsi Code Programming DSC Individual ID Rotate Channel to select the desired ID name for deleting Deleting Address ID/Group IDSet the individual ID and ID name Push DSC/ENT to set the time, and exit the DSC menu Edit the digit of your latitude data by using ChannelEdit the digit of your longitude data by using Channel Edit the digit of the current UTC time by using CHAN- NEL Sentence formatteres ‘GGA,’ ‘GNS,’ ‘GLL’ Position/Time Indication Simple call Distress alert contains defaultDistress Call Normal call Push Distress for 5 sec. to transmit the Distress call Push DSC/ENT to transmit the Individual call Transmitting DSC CallsTransmitting Individual call Transmitting Individual acknowledgement Indv ACK Push DSC/ENT to transmit the Group call Transmitting Group call Push DSC/ENT to transmit the All Ships call Transmitting All Ships call Push DSC/ENT to transmit the Position Request call Transmitting Position Request call Transmitting Position Report call Push DSC/ENT to transmit the Position Report call Transmitting Position Reply callTransmitting Position Report Reply call Receiving an Individual call Receiving DSC CallsReceiving a Distress call Receiving a Distress acknowledgement Receiving a Geographical Area call Receiving an All Ships callReceiving a Distress Relay call Receiving a Position Report Reply call Receiving a Position Request callReceiving a Position Report call Receiving a Position Reply call Rotate Channel to scroll the message Received MessagesDistress message Rotate Channel to select Distress, push DSC/ENT Rotate Channel to select Other, push DSC/ENT Other messages Push DSC/ENT to program and to exit the DSC menu DSC Set ModeOffset time Rotate Channel to select Offset time, push DSC/ENT Push DSC/ENT to exit the DSC menu Mmsi code checkRotate Channel to select Mmsi Check, push DSC/ENT Check the 9-digit Mmsi DSC self ID code FM-3000 caller Push LO/DX IC SCR for 1 sec. to enter Intercom modeOther Functions Intercom Operation Display Backlighting Microphone Lock Function Auto ACK items are not selectable when using FM-3010 Set ModeSet Mode Programming Weather alert Set Mode ItemsScan mode Scan resume timer Internal speaker This item adjusts the contrast of the LCD in 8 stepsDSC watch Beep tone Automatic acknowledgement Attenuation levelScrambler code Antenna Connections Connections and MaintenanceFuse Replacement Cleaning External Speaker Jack Antenna ConnectorNmea in Red/NMEA OUT White Jacks Mounting the Transceiver Using the supplied mounting bracket Attach the clamps on either side of the FM-3000 Using the optional FM-3040 Optional Unit Installation 53.0 ⁄32 Unit mm Dimensions145.0 5 23⁄32 103.0 110.0 4 11⁄32 165.0 6 1⁄2 Problem Possible Cause Solution Troubleshooting Channel List † Low power only Radio license for boaters U.S.A. only Operating Rules Transmitter SpeciﬁcationsSpeciﬁcations General Channel UP/DOWN Keys Y/Z PTT Switch PTT pgsPanel Description Front and side keys SQUELCH/MONITOR/LOCK KEY SQL Moni L VOLUME/DIMMER KEY VOL DIMCHANNEL/DUALWATCH/TRI-WATCH KEY CH/WX DW U/I/C LO/DX IC SCR Top keys 1DUAL/TRI Watch Indicator pgs Volume Indicator pSquelch Indicator p Scan Indicator pgs A. channels Call channel13.3 3 Weather channels Channel group Push Y/Z to select the desired channel Turn power on Set outputPush H/L to select the output power, if necessary Activating the All key lock function Push Y/Z to adjust the backlight levelLock Functions Activating the Lock function Push CH/WX DW U/I/C several Monitor FunctionRF Attenuator Function Push LO/DX to turn the RF Attenuator function on and OFF LO/DX IC SCR to turn Dualwatch/Tri-watch OperationProgramming scramble codes Push Y/Z to select the desired channel To stop the scan, push Scan TAG To cancel the tag channel setting, push Scan TAG for 1 secConvenient Clearing setting all tagged channels Beep tone Beep Entering Set modeTurn power OFF While pushing 16 9 , turn power on Available characters Intercom beep functionPush SQL to move to forward then push Y/Z to se Connection cable FM-3011 6 m 20 ft 13.17 FM-3010 supplied accessoriesAccessories included with the FM-3010 Qty Completed installation should look like this Installation Mm 3⁄32˝ R11 Mm 3⁄32 165 mm 61⁄2 149 mm 57⁄8