Optional Unit Installation | Furuno FM-3000 guide

8.Connections and Maintenance

8.6 Optional Unit Installation

RCAUTION

DISCONNECT the DC power cable from the trans- ceiver before performing any work on the trans- ceiver. Otherwise, there is danger of electric shock and/or equipment damage.

Follow the case opening procedure shown here when you want to install an optional unit.

qRemove the 6 screws as shown below and open the trans- ceiver.

wRemove the 4 screws from the shielding plate, then lift up the shielding plate.

ePlug an optional unit (FM-3030) to J3 on the MAIN unit as shown below.

Optional unit

rReturn the shielding plate and assemble the units to their original positions.

RCAUTION

1.When re-assembling the case and tightening the screws, you must keep the specified torque (0.7±0.1 N.m). Otherwise the transceiver may be damaged (torque too high) or lose waterproof efﬁ- ciency (torque too low).

2.When uninstalling the optional unit, remove it ver- tically. Wiggling the unit from side to side may damage the optional unit's connector.

45

Image 54

Furuno FM-3000 manual Optional Unit Installation

Contents

Marine VHF Radiotelephone Foreword FM-3000 Case of Emergency Do not open the equipment Do not disassemble or modify the equipmentAny repair work must be done by a licensed radio technician Compass Only qualified personal should work in- side the equipmentStandard Steerling Transceiver Table of Contents Installation Setting Tag ChannelsSet Mode Programming Panel Description System Conﬁgulation Vii Standard supply & Options Standard supplyOptions SQL control p ControlsFront Panel HI/LO key Distress key LO/DX IC SCR key16 9 key CH/WX DW U/I/C key Function Display Microphone Channel Basic OperationChannel Selection Channel 9 Call channel Change the channel group, if necessary Push once When Weather alert is OFF A. channels Or twiceWeather channels Rotate Channel to select a channel Push HI/LO to select the output power, if necessary Receiving and Transmitting Call Channel Programming Channel CommentsPush Activating the Scrambler Set mode Scrambler code itemOptional Voice Scrambler Operation Programming scrambler codes Operation Dualwatch/Tri-WatchDescription Again Example Operating Tri-watch on INT Channel Scan Operation Scan Types Starting a Scan Setting Tag ChannelsConvinient Clearing setting all tagged channels Scan starts DSC Individual ID DSC OperationMmsi Code Programming Programming Address ID/Group ID Deleting Address ID/Group ID Set the individual ID and ID nameRotate Channel to select the desired ID name for deleting Edit the digit of the current UTC time by using CHAN- NEL Edit the digit of your latitude data by using ChannelEdit the digit of your longitude data by using Channel Push DSC/ENT to set the time, and exit the DSC menu Position/Time Indication Sentence formatteres ‘GGA,’ ‘GNS,’ ‘GLL’ Distress alert contains default Distress CallSimple call Normal call Push Distress for 5 sec. to transmit the Distress call Transmitting DSC Calls Transmitting Individual callPush DSC/ENT to transmit the Individual call Transmitting Individual acknowledgement Indv ACK Transmitting Group call Push DSC/ENT to transmit the Group call Transmitting All Ships call Push DSC/ENT to transmit the All Ships call Transmitting Position Request call Push DSC/ENT to transmit the Position Request call Transmitting Position Report call Transmitting Position Reply call Transmitting Position Report Reply callPush DSC/ENT to transmit the Position Report call Receiving a Distress acknowledgement Receiving DSC CallsReceiving a Distress call Receiving an Individual call Receiving an All Ships call Receiving a Distress Relay callReceiving a Geographical Area call Receiving a Position Reply call Receiving a Position Request callReceiving a Position Report call Receiving a Position Report Reply call Rotate Channel to select Distress, push DSC/ENT Received MessagesDistress message Rotate Channel to scroll the message Other messages Rotate Channel to select Other, push DSC/ENT Rotate Channel to select Offset time, push DSC/ENT DSC Set ModeOffset time Push DSC/ENT to program and to exit the DSC menu Check the 9-digit Mmsi DSC self ID code Mmsi code checkRotate Channel to select Mmsi Check, push DSC/ENT Push DSC/ENT to exit the DSC menu Intercom Operation Push LO/DX IC SCR for 1 sec. to enter Intercom modeOther Functions FM-3000 caller Microphone Lock Function Display Backlighting Set Mode Set Mode ProgrammingAuto ACK items are not selectable when using FM-3010 Scan resume timer Set Mode ItemsScan mode Weather alert Beep tone This item adjusts the contrast of the LCD in 8 stepsDSC watch Internal speaker Attenuation level Scrambler codeAutomatic acknowledgement Cleaning Connections and MaintenanceFuse Replacement Antenna Connections Antenna Connector Nmea in Red/NMEA OUT White JacksExternal Speaker Jack Using the supplied mounting bracket Mounting the Transceiver Using the optional FM-3040 Attach the clamps on either side of the FM-3000 Optional Unit Installation Dimensions 145.0 5 23⁄32 103.0 110.0 4 11⁄32 165.0 6 1⁄253.0 ⁄32 Unit mm Troubleshooting Problem Possible Cause Solution † Low power only Channel List Operating Rules Radio license for boaters U.S.A. only General SpeciﬁcationsSpeciﬁcations Transmitter Front and side keys PTT Switch PTT pgsPanel Description Channel UP/DOWN Keys Y/Z LO/DX IC SCR VOLUME/DIMMER KEY VOL DIMCHANNEL/DUALWATCH/TRI-WATCH KEY CH/WX DW U/I/C SQUELCH/MONITOR/LOCK KEY SQL Moni L Top keys Scan Indicator pgs Volume Indicator pSquelch Indicator p 1DUAL/TRI Watch Indicator pgs Channel group Call channel13.3 3 Weather channels A. channels Turn power on Set output Push H/L to select the output power, if necessaryPush Y/Z to select the desired channel Activating the Lock function Push Y/Z to adjust the backlight levelLock Functions Activating the All key lock function Push LO/DX to turn the RF Attenuator function on and OFF Monitor FunctionRF Attenuator Function Push CH/WX DW U/I/C several Push Y/Z to select the desired channel Dualwatch/Tri-watch OperationProgramming scramble codes LO/DX IC SCR to turn To cancel the tag channel setting, push Scan TAG for 1 sec Convenient Clearing setting all tagged channelsTo stop the scan, push Scan TAG Entering Set mode Turn power OFF While pushing 16 9 , turn power onBeep tone Beep Intercom beep function Push SQL to move to forward then push Y/Z to seAvailable characters 13.17 FM-3010 supplied accessories Accessories included with the FM-3010 QtyConnection cable FM-3011 6 m 20 ft Installation Completed installation should look like this Mm 3⁄32˝ 165 mm 61⁄2 149 mm 57⁄8 R11 Mm 3⁄32