3.3 CONNECTOR ASSEMBLY
NOTE: Contacts cannot be removed from the connector without the use of the appropriate AMP extraction tool which is available from Pelco.
Installation and/or testing will require you to assemble the connector parts pro- vided. Fabricate the interconnecting cable according to the following steps (refer- ence Figure 2).
1.Slide part A of the cable clamp (item 1) over the end of the cable (item 1, part C) with the threaded end of the cable clamp facing the connector (item 5).
2.If the cable has a diameter less than 1/2 inch (1.3 cm), slide the rubber boot (item 2) over the end of the cable and pull through the cable clamp to so that the boot encases the cable and forms a good seal.
3.Strip back the cable jacket approximately
4.The contact pins supplied with the mating connector are the “crimp” type which may also be soldered if you so desired (item 4).
5.After crimping or soldering the contact pins to the conductors, push them into the proper holes in the connector until they snap in place.
6.Slide part A of the cable clamp toward the connector and screw the parts together. Attach part B (item 1) onto part A and connect both parts with the screws provided.
7.Connect the cable assembly to the unit and seat the connector by twisting the locking collar until it snaps into position.
5 |
|
|
|
|
|
|
|
|
|
| 1 |
|
| ||||
|
|
|
|
|
|
|
| |
|
| threaded end of |
|
|
|
|
|
|
|
|
|
|
| ||||
|
| cable clamp |
| A |
| B |
| C |
|
|
|
|
|
|
|
|
|
STEP 1 |
5FLEXIBLE RUBBER BOOT
STEP 2
2
1
A B
C
| 5 ** |
|
|
|
| 3 |
|
| 1 |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
|
|
| 4 |
|
| STRIP 1/8" |
| A | B |
|
|
|
|
|
|
|
|
| |
STEPS |
|
|
|
|
|
|
|
| C |
|
|
| CRIMP | CRIMP |
|
|
|
| |
|
|
| INSULATION |
|
|
|
| ||
|
|
| WIRE |
|
|
|
|
|
|
|
|
|
|
|
|
| OUTSIDE |
|
|
|
|
|
|
|
| STRIP 1" | JACKET |
|
|
|
|
|
|
|
| OF CABLE |
|
| |
|
|
|
|
|
|
|
|
| |
** | 4 |
| 1 |
| 3 | 1 |
| 2 | 1 |
9 |
|
| 5 |
| |||||
|
|
|
|
|
| ||||
ITEM 5 DETAIL |
|
| 8 |
| 4 |
|
| ||
15 |
|
| 10 |
| 6 | 3 | |||
|
|
| 14 |
| 9 | ||||
|
|
|
|
|
|
|
| ||
| 22 |
|
| 16 |
|
|
| 10 |
|
| 28 |
|
|
| 20 |
| 15 | 7 | |
|
|
| 23 |
|
| ||||
| 33 |
|
| 25 |
|
|
|
| |
|
| 29 |
|
| 21 | 14 | 11 | ||
|
| 37 |
| 28 |
| ||||
|
| 34 |
| 26 |
| 16 | 15 | ||
|
|
|
|
|
| ||||
|
|
| FRONT VIEW |
|
|
| |||
|
|
|
|
| FRONT VIEW |
|
| FRONT VIEW | |
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
THE MOST COMMONLY USED CONNECTOR
3 | 1 |
| 3 | 1 |
|
|
| ||
7 |
| 4 |
| 4 |
|
| 6 | ||
|
|
| ||
|
|
|
| |
11 |
| 8 |
|
|
|
| 9 | 7 | |
| 14 |
| ||
|
|
|
| |
| 12 |
|
| FRONT VIEW |
| FRONT VIEW |
|
| |
|
|
|
Figure 2. Connector Assembly
PELCO Manual | 7 |