5 REINSTALL THE SLIDING PANEL
TWO OR MORE PEOPLE WILL BE REQUIRED TO HANDLE THE PANEL SAFELY.
A. Insert door panel. From the interior of the building, tilt |
|
|
|
| |||
the top of the panel toward the door frame and insert the |
|
|
| x | |||
top of the door panel into the top track. Move the bottom |
|
|
| ||||
of the panel toward the door frame until it is vertical. |
|
|
|
| |||
Gently set the panel down into the bottom track. |
|
|
|
|
| ||
Note: Make sure the top of the panel clears the anti- |
|
|
|
| |||
lift clip before attempting to place the panel on the |
|
|
|
| |||
bottom track. |
|
|
|
|
|
| |
B. Adjust the rollers so that the slide panel runs freely and |
|
|
|
| |||
is parallel to the fixed interlocker. Rotate roller adjustment |
| 4MJEFQBOFM | x | ||||
screws clockwise to raise the panel or |
| 3PMMFSBEKVTUNFOUTDSFX | |||||
lower the panel. They are located at the bottom of the slide | |||||||
|
|
| |||||
panel at both ends. Once plumb, adjust the slide panel to |
|
|
|
| |||
the proper height to attain even coverage of the weatherstrip |
|
|
| ||||
at both the top and bottom as viewed from the exterior. | 4JMM |
|
|
| |||
|
|
|
|
|
| ||
C. Identify the keeper in |
|
|
|
|
| *OUFSJPS7JFX | |
|
|
|
|
|
| ||
the hardware package |
| Interior handle |
|
|
| ||
and perform the keeper |
|
|
|
| |||
|
| Lock | 5C |
|
| ||
attachment steps based |
|
|
|
| |||
| adjustment |
|
|
| |||
on which keeper is in the |
|
| screw |
|
|
| |
| Lock hook |
|
|
| |||
package. |
| Shank |
|
|
| ||
Determine the keeper |
|
|
|
| |||
|
|
|
|
|
| ||
location by opening the panel a few |
| Mortise lock |
|
|
| ||
inches, and extending the lock hook. |
|
|
|
|
|
| |
With a pencil, mark the location on |
| Handle latch |
|
|
| ||
the jamb directly across from the top |
|
|
|
| |||
|
|
|
|
|
| ||
of the shank. | 5D |
| #6 x 1/2" | 5E |
|
| |
|
| Starter |
|
| |||
D. Place the keeper with 4 screw holes |
|
| screw |
|
| Keeper | |
|
|
|
|
| |||
on the jamb so the top of the slot is |
|
|
|
|
|
| |
aligned with the pencil mark. Attach |
|
|
|
|
|
| |
by inserting a #6 x ½” starter screw |
| Keeper |
|
|
|
| |
into one of the slotted keeper holes. |
|
|
|
|
|
| |
E. Place the keeper with 2 screw holes |
| Shim |
|
|
|
| |
on the jamb by “snapping” it into the | 5F |
| 5F | Shim |
| ||
frame jamb at the desired location. |
|
|
|
|
|
| |
The keeper may be moved up or |
|
|
|
|
|
| |
down to align with the pencil mark. |
|
|
|
|
|
| |
The keeper will stay in position until |
|
|
|
|
|
| |
attached with screws. |
|
|
|
|
|
| |
F. Insert a shim between the frame jamb |
|
| Loosen |
|
|
| |
and the rough opening at the keeper |
|
|
|
|
| ||
|
|
| 5H |
|
| ||
location. |
|
|
|
|
| ||
G. Adjust the lock hook by turning the |
|
|
|
|
|
| |
door lock adjustment screw clockwise |
| 5G | Tighten |
|
|
| |
to loosen or |
|
|
|
| |||
|
|
|
|
|
| ||
tighten until the mortise lock is |
|
|
|
|
|
| |
aligned properly, the door locks easily, |
|
|
|
|
|
| |
and there is less than 1/16" movement |
|
|
| 5H |
|
| |
when the door is locked. |
|
|
|
|
| ||
|
|
|
|
|
|
H. Install the keeper by inserting 3" long screws (provided) through the keeper holes, the shim and into the rough opening frame members. Remove the starter screw from the 4 screw hole keeper and replace it with a 3" long screw.