Philips 55PFL4706, 40PFL4706 Changing picture and sound settings, Changing picture settings

Changing picture and sound settings

You must set [Home] in [Location]. (Refer to page 30.)

Otherwise, personalized picture and sound settings will not be memorized after the unit goes to standby mode.

Changing picture settings

1 Press MENU on the remote control.

2 Use Î/ï/ Í/Æ to select [Setup] > [Picture]

Setting items
				Description
	Color		Off	Sets Color enhancement to off.
enhancement			On		Makes colors more vivid bright colors.
			Off	Sets Active control to off.
			On with	Adjusts backlight for the best picture quality by
Active control			Light	dynamically adjusting the backlight intensity in
			Sensor	accordance with lighting condition in the room.
			On without	Adjusts backlight for best picture quality based
			Light	on the incoming video signal.
			Sensor
			Automatic
			Super zoom
		4:3
			Movie
	Picture format		expand 14:9 Refer to ‘Summary of picture formats’ on
				page 23.
			Movie
			expand 16:9
			Wide

Picture

Sound

Features Installation

Software

Settings assistant	Start now
Contrast
Brightness
Color
Tint
Sharpness
Color temperature	Cool
Dynamic contrast	Off

	screen
	Unscaled
	PC	Turns off image enhancement features which
Mode selection		makes the TV to act purely as a monitor.
	HDTV	Enables image enhancement features to
		improve picture quality.
Auto adjustment		The horizontal / vertical position, clock and
		phase of the PC screen are automatically
		adjusted.
Clock		Setting to stabilize the PC screen.
Phase		Setting to improve the clarity of the PC screen.
Horizontal shift		Adjusts the horizontal position of the picture
		for PC screen.

3 Use Î/ï/ Í/Æ to select one of the picture settings, and press OK to enter the setting.

4 Adjust the picture quality.

The following picture settings can be configured. Depending on the format of the picture source, some picture settings are not available.

Setting items		Description
Settings assistant		Use [Settings assistant] to guide you through
		the best picture settings.
Contrast		Adjusts the intensity of bright areas, keeping
		dark areas unchanged.
Brightness		Adjusts the intensity and details of dark areas.
Color		Adjusts color intensity.
Tint		Adjusts the color balance in an image.
Sharpness		Adjusts the level of sharpness in image details.
Color	Cool	More blue tones.
	Normal	Standard tones.
temperature
	Warm	More orange tones.
Dynamic	Off	Sets Dynamic contrast to off.
contrast	On	Automatically enhances contrast in an image.
Digital Natural	Off	Sets Digital Natural Motion to off.
Motion	Minimum	Reduces judder in video using low intensity
(Available for		frame interpolation to make the video smooth.
55PFL4706
	Maximum	Reduces judder in video using high intensity
only)
		frame interpolation to make the video smooth.
Noise	Off	Sets Noise reduction to off.
reduction	On	Reduces noise in an image.
MPEG artifact	Off	Sets MPEG artifact reduction to off.
		Reduces a blockiness and a blurriness and
reduction	On
		judder by digital filter.

Vertical shift	Adjusts the vertical position of the picture for
	PC screen.

5 Press MENU to exit.

Note

•[Mode selection] will not be displayed when incoming signals are other than 720 x 480p 60Hz, 1280 x 720p 60Hz and 1920 x 1080p 24 / 30 / 60Hz.

•[Digital Natural Motion] (Available for 55PFL4706 only) If the input video contains adjacent video frames with inherent motion blur captured by the video camera, [Digital Natural Motion] will interpolate blur and cause streaking artifacts in high motion scenes. If the content you are watching causes a lot of Interpolation Induced Blur Amplification, it is best to turn off [Digital Natural Motion] temporarily.

•[Digital Natural Motion] (Available for 55PFL4706 only) uses frame interpolation to make the video appear smooth which causes a video lag of about 200 milliseconds. If you are using the TV for gaming or as a PC monitor DNM will introduce lag. If your gaming system has a lag adjustment feature for your game controller, use it to negate the lag or else turn off DNM for any application where lag is an issue. If your prefer to use DNM while watching movies on your Home Theater PC (HTPC) and are using an external Audio Receiver for sound output, set a 200 millisecond delay on your audio output for A/V sync. You will not experience A/V sync issues for anything other than gaming or HTPC applications since the TV has internal A/V sync functionality.

22EN