HW.qxd 17.06.03 12:05 Seite 4
English
▼
Deutsch▼ Français▼ Nederlands▼ Italiano▼ Español
▼
êÛÒÒÍËÈ
GettingStarted
1. Switching the Voice Tracer on
Press the PLAY/PAUSE/REMAIN or the REC/PAUSE button to activate the Voice Tracer.
The device will switch to standby mode. When you insert the batteries, the LCD displays all indicators
and the Voice Tracer goes into standby mode (Figure 2).
SwitchingtheVoiceTraceroff | Figure 2 |
The power will shut off automatically if you do not |
|
activate any functions for 1 minute. |
|
2.Lock Function (Hold)
1.Press and hold the MENU/HOLD button for approximately 2 seconds when the Voice Tracer is in playback, recording or standby mode to activate the lock function (HOLD ON -
Figure 3). All buttons are deactivated when the device is in HOLD mode, and the LCD displays “ON HOLD” when a button is pressed.
2. Press and hold the MENU/HOLD button again for approximately 2 seconds to release the lock function (Figure 4). The LCD will display “OF HOLD” indicating that the lock function has been deactivated.
HOLD mode will be deactivated if the device switches off and is turned on again.
Recording | Figure 4 |
|
Please note the following before you start recording.
Check that the device is in standby mode.
➤Press the FOLDER/REPEAT button to select the desired folder. The Voice Tracer will move to the next folder (A, B, C, or D) each time you press the button. If you do not select a folder, you will record in the current folder.
Folder (select A, B, C or D)
➤When the number of files in the current folder reaches 99, the recording will continue after the last file of the next folder.
➤Press the PLAY/PAUSE/REMAIN button to display the remaining recording capacity.
➤Press the NEXT button 
to separate a FILE while you are recording (file separation function).
➤The maximum number of files in each folder is 99 (up to 396 files: 99 x 4 ).
➤ If the recording time exceeds the available capacity or the file number reaches 396, “FULL” is displayed and you cannot continue recording (Figure 5).
If this happens, delete some recordings or move them to an external device (audio or PC) to continue recording.
➤Do not remove the batteries during Recording.
This may cause the Voice Tracer to malfunction. If you intend to record for a prolonged period of time, replace the batteries before beginning recording.
➤Recording will stop automatically when no
sound is detected when the Voice Tracer is in
VOR mode (Figure 6).
Deactivate the VOR function when recording
important conversations.
Figure 6
VoiceRecording
Set the desired recording sensitivity, folder, VOR function and speed (SP or LP) before you start recording (see Pages 7 and 8).
| Recording with the |
|
|
|
1. | Point the device's |
|
|
|
| the sound source. |
|
|
|
2. | Press the REC/PAUSE button to start recording. |
|
|
|
|
|
| ||
| The red LED will light |
|
|
|
| (Figure 7 and 8). |
|
|
|
3. | Press the REC/PAUSE button to pause the | Figure 7 | ||
| recording. The red LED will blink |
|
|
|
| (Figure 9). |
|
|
|
4. | Press the REC/PAUSE button again to continue |
|
|
|
|
|
| ||
| the recording. The red LED will light again. |
|
|
|
5. | Press the STOP/DEL button to stop recording. |
|
|
|
To record with an external microphone, connect | Figure 8 | |||
|
|
| ||
the microphone to the microphone socket and follow the same procedure as for the
Figure 9
