BDL3245E / BDL4245E / BDL4645E
4.2.5. Configuration1 menu
• {Pixel shift} - Select the time interval ({Auto} / {10 ~ 900} Seconds |
/ {Off}) for the display to slightly expand the image size and shift the |
Picture
Screen
Audio
PIP
Configuration1
Configuration2
Advanced option
Switch on state Auto adjust Power save Language Panel saving Color system Network control port Network settings Configuration reset Factory reset
position of pixels in four directions (up, down, left, or right). |
NOTE: The default {Auto} setting for menu item Pixel shift does not support menu items Zoom mode, H/V Position, and PIP.
Color system
Selects the Color System depends on your input video format.
The options are: {Auto} / {NTSC} / {PAL} / {SECAM} / {4.43NTSC} /
NOTE: This item is functional for
Network control port
Select the nectwork control port.
The options are: {RS232} / {LAN(RJ45)}.
Switch on state
Select the display status used for the next powering on.
•{Power off} - The display will remain off when the power cord is connected to a wall outlet.
•{Forced on} - The display will turn on when the power cord is connected to a wall outlet.
•{Last status} - The display will return to the previous power status (on/off/standby) when removing and replacing the power cord.
Auto adjust
Use this function to let the display automatically optimize the display of VGA input image.
NOTE: This item is functional for VGA input only.
Power save
Set the display to reduce the power automatically.
•{RGB} - Select {On} to let the display enter DPMS mode when no signal detected from the HDMI Graphic mode, HDMI,
•{VIDEO} - Select {On} to let the display enter power saving mode when no signal detected from the HDMI Video mode or YPbPr inputs after three successive cycles.
Language
Select the language used in the OSD menu.
The options are: {
} / {
} / { 
} / {
} / {
} /
{
} / {
} / {
} / {
}.
Panel saving
Choose to enable the panel saving functions to reduce the risk of the “image persistence”.
•{Cooling Fan} - Select {On} to turn on the cooling fan all the time. Select {Auto} to turn on/off the cooling fan according to the display’s temperature.
NOTES:
•The default {Auto} option will start running the cooling fan if the temperature of 65°C (152°F) is reached, and will keep running for 30 minutes after cooling down to the temperature of 62°C (144°F).
•A
•{Brightness} - Select {On} and the brightness of the image will be reduced to an appropriate level, and the Brightness setting in the Picture menu will become unavailable.
NOTE: If {LAN(RJ45)} is selected, then {RS232} will not be activated, even if a cable is attached, and vice versa.
Network settings
Assign {IP address}, {Subnet Mask}, and {Default gateway} for the display.
Network settings
Network host name |
| 9 |
| 0 | Z | L |
|
|
|
DHCP |
|
|
|
| Disable |
|
|
| |
IP address | 172 | - | 16 | - | 0 | - | 1 | ||
Subnet mask | 255 | - | 255 | - | 0 | - | 0 | ||
Default gateway | 0 |
| - | 0 | - | 0 | - | 0 | |
Login user name |
| a | d | m i | n |
|
|
| |
Login password | 0 |
| 0 | 0 |
| 0 |
|
| |
| [ SET ] |
|
|
|
|
|
| ||
change [SET] in STORE
•DHCP - Choose to enable or disable the DHCP function. If enabled, the display will be assigned IP address, Subnet mask and Default gateway automatically. If disabled, you will be prompted to enter the following value manually. Finally, press [SET] button to store and save the chosen values.
•IP address
•Subnet mask
•Default gateway
•Login user name (The default user name is {admin})
•Login password (The default password is {0000})
Configuration reset
Reset all settings in the Configuration1 menu to factory preset values.
Factory reset
Reset all the settings in the OSD menus of {Picture}, {Screen}, {Audio}, {PIP}, {Configuration1}, {Configuration2}, and {Advanced option} to factory preset values.
Press [
] or [ ] button to select [Reset], and then press [SET] button to do the reset.
Factory reset
Cancel |
| Reset |
|
|
|
18
