External Input Mode (for VCR features)
To receive the signal from an external input (decoder, satellite receiver, video camera, another VCR etc.), connect to the AV2 (DECODER) socket, and enter “002” with numerical key pads button to appear “AV2” on the TV screen.
If you use the AV1 (TV) socket, enter “001” with numerical key pads to appear “AV1” on the TV screen.
If you use the front AUDIO/VIDEO input jacks, enter “003” with numerical key pads to appear “AV3” on the TV screen.
Inserting batteries into the Remote Control
1Open the battery cover.
2 Insert batteries (AA size) with the correct polarity as indicated by the + and - symbols inside the battery compartment.
3Close the cover.
CAUTION!
–Remove batteries if they are exhausted or not to be used for a long time.
–Do not use old and new or different types of batteries in combination.
–Batteries contain chemical substances, so they should be disposed off properly and kept away from children.
Using the Remote Control
•Direct the remote control at the remote sensor of the DVD/VCR.
•Do not drop the remote control.
•Do not leave the remote control near extremely hot or humid place.
•Do not spill water or put anything wet on the remote con- trol.
Playable Video Cassette Tapes
Philips Consume Electronics recommends that only video cas- sette tapes that have the VHS mark and High Quality (HQ) sys- tem is compatible with this DVD/VCR.This
DVD/VCR has an Automatic Head Cleaner.
| Recording Prevention | 1 |
| Video cassette tapes have record tabs to | |
1 | ensure recordings are not erased accidentally. | |
To prevent recording, break off the tab with a |
| |
2 | 2 | |
To allow recording, cover the hole with cello- | ||
| phane tape. |
Notes:
–Use only tapes with VHS mark.
–Remove any adhesive
–Periodic maintenance is required to maintain your DVD/VCR performance.
–Video heads will require replacement after a period of time. Only an authorised service center should perform this service.
Turning on your DVD/VCR
| The following steps only be performed when you insert the AC | English | ||
1 | PLUG at the first time. | SELECT K L |
| |
Turn on the TV and select the |
|
| ||
→ ENGLISH |
|
| ||
| video channel on the TV. |
|
| |
2 | FRANÇAIS |
|
| |
Plug in the DVD/VCR. |
|
| ||
ESPAÑOL |
|
| ||
3 | Press K/L repeatedly to select | DEUTSCH |
|
|
| your desired language. | ITALIANO |
|
|
4 | SVENSKA |
|
| |
Press DISC/VCR MENU. | NEDERLANDS |
|
| |
5 | Confirm with P+. | PUSH MENU TO CONTINUE |
| |
|
|
| ||
| The automatic TV channel search |
|
|
|
6 | starts. |
|
|
|
'TIME' and 'DATE' will appear on | PLEASE WAIT |
|
| |
7 | the TV screen. |
|
|
|
Check 'TIME'. If required, please | START | FINISH |
| |
| change the time with numerical key | ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ |
| |
8 | pads. |
|
|
|
Check if the displayed settings for |
|
|
| |
| 'DAY', 'MONTH' and 'YEAR' are |
|
|
|
9 | correct. | TIME |
|
|
When all information is correct, |
|
| ||
|
|
| ||
| save by pressing STATUS/EXIT.The | DATE |
|
|
| preparation for use is now com- | SMART CLOCK [ON] |
| |
| plete. |
| ||
|
|
|
| |
|
| END=EXIT |
|
|
| Notes: |
|
|
|
| – If the DVD/VCR has been completed AUTO TUNING at |
| ||
| this procedure, this initial menu has never shown even if |
| ||
| power failure is occured or inserted AC plug again.) |
| ||
Video Channel Setting
Video channel setting will be necessary, if your DVD/VCR is connected to the TV via the coaxial cable.
1Insert a
If playback does not start, press PLAY B .
2Select and adjust your TV to channel 36.
•If the playback picture appears on the TV screen, continue with step 8.
•If channel 36 is employed for broadcasting, or interference lines appear on the picture, the RF converter must be set to a different channel between CH22 and CH69. Continue with step 3.
3Press DISC/VCR MENU.
4Press K/L to select INITIAL SET
| UP.Then, press B. | SELECT K L CHOOSE B |
5 | Press K/L to select RF OUT.Then, | → RF OUT CH 36 |
| press B twice. |
|
6 | Press K/L to select a channel |
|
| which is not used for broadcasted |
|
between channel 22 and channel 69
END=EXIT
in your area, then press B.
•You can also see the selecting RF channel in the display 7 Press STATUS/EXIT to exit.
Set the TV channel to the RF OUT CHANNEL which was selected on the DVD/VCR. A picture from the VCR will appear on the TV screen. If a picture does not appear, repeat steps 3 to 7 using a different channel which is not used for broadcast- ed.
8 Press STOP C to stop the tape.
Note:
–You may also access the RF OUT CH menu by pressing and holding DISC/VCR MENU for 3 seconds during power off until the RF OUT CH menu appears.
7
