Philips Network Adaper owner manual NEL. Discussed below are the options

Net 1Card IB 2/15/00 12:18 PM Page 28

TRANSMITTER CONTROL

If you select “LOCK” under “RCVR LOCKOUT,” you have a couple of options in regards to “RCVR POWER,” “RCVR VOLUME,” and “RCVR CHAN-

NEL.” Discussed below are the options.

OPTION 1: If you selected a setting (other than “CUR- RENT”) for any of the three categories – Power, Volume, Channel – the Receiver TVs will be locked into those settings and can only be changed by the the Transmitter TV. Also, “P,” “V,” or “C” will appear at the top of the menu indicating that Power, Volume, or Channel has been locked. You can lock one, two, or all three. For example, if you set all TVs to “RCVR POWER ON,” “RCVR VOLUME 35,” and “RCVR CHANNEL 40,” then all TVs will power on, set their volumes at 35, and tune to Channel 40. Also, none of the Receiver TVs can be adjusted, except by you, and you can even make changes without releasing the lock.

TRANSMITTER CONTROL

*** (PVC) CTRL LOCK***

BROADCAST	ALL SETS
RCVR POWER	ON
RCVR VOLUME	35
RCVR CHANNEL	40
RCVR LOCKOUT	LOCK
UPDATE RCVR TVS
EXIT MENU

PRESS +TO UPDATE RCVRS

OPTION 2: If you selected “CURRENT” for any or all of the settings, the Receiver TVs can make adjustments to either Power, Volume, or Channel. For example, if you left “RCVR VOLUME” at the default “CURRENT,” then the Receiver TVs could be adjusted at the TV to the best volume for the model of TV and the location.

TRANSMITTER CONTROL

*** (P–C)	CTRL LOCK***
BROADCAST		ALL SETS
RCVR POWER		ON
RCVR VOLUME		CURRENT
RCVR CHANNEL		40
RCVR LOCKOUT		LOCK
UPDATE RCVR TVS
EXIT MENU

PRESS +TO UPDATE RCVRS

28

TRANSMITTER CONTROL

Once you have transmitted your message, you will probably want to return control of the Receiver TVs

back to those TVs. If you selected “UNLOCKED” from the ”RCVR LOCKOUT”sub-menu, then each TV has to be reset at that TV. However, if you selected “LOCK,” the locked TVs can be restored to their previous power, channel, and cable settings from the Transmitter TV.

BEGIN

If not already in the “TRANSMITTER CON- TROL” menu, press the D button on the remote control. Then press the ▼ button until “RCVR LOCKOUT” is highlighted.

Press the – (◀) or + (♣) button until “RESTORE” is selected. (Note: you can also select “UNLOCK” from this menu. Doing so, releases the Transmitter TV’s lock on all Receiver TVs, but does not retore the Receiver TVs to their previous settings.)

Press the ▼ button until “UPDATE RCVR TVS” is highlighted. Then, press the – (◀) or + (♣) button. “CURRENT” will appear beside “RCVR POWER” and “RCVR CHANNEL.” The TV’s power, channel, and cable are now restored to their previous settings. Receiver Volume will have to be adjusted at each TV.

When finished, press the ▼ button to highlight “EXIT.” Then press the “M” button. Or you can exit by simply pressing the RECALL button when you’re done.

TRANSMITTER CONTROL
*** (P–C)	CTRL LOCK***
BROADCAST		ALL SETS
RCVR POWER		ON
RCVR VOLUME		CURRENT
RCVR CHANNEL		40
RCVR LOCKOUT		RESTORE
					TRANSMITTER CONTROL
UPDATE RCVR TVS
				ADDRESS TYPE		BROADCAST
EXIT MENU
				BROADCAST		ALL SETS
PRESS +TO UPDATE RCVRS
			RCVR POWER			CURRENT
			RCVR VOLUME			CURRENT
			RCVR CHANNEL			CURRENT
			RCVR LOCKOUT			UNLOCKED
			UPDATE RCVR TVS
			EXIT MENU
			PRESS + TO UPDATE RCVRS

29