Specifications | Philips VRB613AT, VRB413AT manual

50 Specifications

Video Heads

Four heads – Hi-Fi (VRB613)

Four heads (VRB413)

Video Signal

EIA standards; NTSC color

Antenna

VHF/UHF – 75 ohm external antenna terminal

VHF Output Signal

Channel 03 or 04 (switchable) 75 ohms unbalanced

Power Requirement

120V AC; 60Hz

Power Consumption

14W (VRB613)

12W (VRB413)

Operating Temperature

41°F (5°C) to 104°F (40°C)

Relative Humidity

10% to 80%

Weight

5.5lbs. (2.5 kg.) (VRB613)

5.3Ibs. (2.4 kg.) (VRB413)

Dimensions

14-3/16” (W) x 3-5/8” (H) x 8-3/4” (D) (360mm x 92mm x 223mm)

Tuner Broadcast Channels

VHF 2-13, UHF 14-69

Cable TV Channels

1-125

NOTE: Designs and specifications are subject to change without notice.

Image 50

Philips VRB613AT, VRB413AT owner manual Specifications

Contents

VRB413AT VRB613AT This bolt of lightning indi- cates uninsulated material Dear Philips product ownerFor Customer Use Model No Serial No Introduction FeaturesSafety Precautions Declaration of Conformity Table of Contents Before Using Your VCR Hookups without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TV Hookups without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCR Recording/Viewing Any Channel Hookups with a Cable Box/Direct Broadcast SystemConnections TV’s Antenna Cable Signal Cable Box/DBSRecording One Channel/Watching Another VRB413 Hookups with a Stereo TVVRB613 2Turn on the TV Press the VCR button, then press the Power buttonTurning on Your VCR Press the Menu button. The display shown below will appear VRB613 only Automatic Channel SetupPress the VCR button Press the Menu button Press the STATUS/EXIT button Automatic Channel Setup cont’dAdding/Deleting Channels Reviewing Memorized Channels Press the STATUS/EXIT button once or twice to exit Do each step within 60 seconds of the previous step Setting the ClockManual Clock Setting Setting the Clock cont’d Enter a 0 before a single-digit number Automatic Clock Setting Press the VCR button, then press the Menu button Time Zone Daylight-Savings Time Press the VCR button Language Selection Setting the Remote to Operate a TV Your VCR remote control may operate your TV. If the remote 2Find Your code Eject Button Remote Control ButtonsVOLume o/p Button Press to adjust the volume of your TV VCR Button Press to operate the TV Remote Control Buttons cont’dTV Button If you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFF Cassette Compartment Timer LightVCR Display Panel VCR Light Remote Sensor Power ButtonFWD Fast Forward Button REWind Button Rear Panel Read and follow the steps below to play a tape PlayingVHS Quasi Play Back Sqpb 1Turn on the TV 2Insert a tape in the VCR VCR light does not appear, press the VCR/TV button once RecordingIf the VCR light appears on the display panel, go to . If RECord light will appear Recording One Channel/Watching Another One-Touch Recording OTR CH12 Timer Recording Daily Timer Recording cont’d Time OFF To Correct Push Clear To END Push Exit Press the STATUS/EXIT button. Program WAS COM Tape Speeds Checking or Cancelling Timer Recordings Rerecording Tape Duplication RF coaxial cable Press the F.FWD/B button so that on appears beside VCR SET UP, then press the F.FWD/B buttonRepeat Play Real-Time Counter Memory Press the STATUS/EXIT button to see the status display Time Search Press the VCR button Press the Time Search button Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still Picture Automatic Operation Features Monitor Understanding On-Screen DisplaysSpecifically… Multi-Channel Television Sound System VRB613 only cont’d Press the RECord/OTR button to start recording Hi-Fi Stereo Sound System VRB613 only Blue Background Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 or Specifications Renewed Index Page Page Page Supplied Accessories