Pioneer BDP-95FD Changing the output video resolution, Connecting using an S-Video output, Auto

02Changing the output video resolution

Use the OUTPUT RESOLUTION button located on both the front panel and the remote control to switch the output video resolution for the HDMI and component video outputs.

The table below shows the output settings.

Setting	HDMI output	Component	Video/S-Video
		output	output
AUTO	TV’s preferred	TV’s preferred	480/60i
	resolution1,2	resolution3
480i	480/60i	480/60i	480/60i
480p	480/60p	480/60p	480/60i
720p	720/60p	720/60p 4,5	480/60i
1080i	1080/60i	1080/60i4,5	480/60i
1080p	1080/60p	480/60i	480/60i
Source	Dependent on	Dependent on	480/60i
Direct	source1,2	source 2,5,6,

1.Refer to 24p output below for conditions.

2.The video output will be interrupted when switching the video output.

3.For resolutions that cannot be output by component output, video is output in the following resolutions: 480/60i

4.Video output is 480i during copy protected DVD-Video playback.

5.Video output during BD-ROM playback is 480i depending on the disc.

6.The frame frequency for 1080/24p is still 60 Hz.

Note

•Depending on your display, some of the settings may result in the picture disappearing. In this case, press

OUTPUT RESOLUTION repeatedly until the picture re-appears.

•1080/60p and 1080/24p output is only compatible with HDMI displays. They are not compatible with the component video output.

•When output video resolution is set to 720p, 1080i or 1080p, video is output in 16:9 format even if TV Aspect Ratio (page 41) is set to 4:3 (Standard).

•If the contours of the displayed subjects look jagged or blurred, try setting the output video resolution to 480i. (If you connected this player to your TV with the HDMI connection and the picture disappears when you switch the output video resolution to 480i, use the component connection with the 480i output video resolution or S-Video, the standard composite connection instead.)

•Note that when using a Component Video connection with a TV or other AV component (not using HDMI), 480/60i video may be output in 480/60p.

24p output

For smooth presentation of 1080/24p or 720/24p video with an HDMI-equipped display compatible with 1080/24p input, set 24p Direct Out (page 41) on this player to On.

This player will output 1080/24p video over HDMI in the following cases:

•1080/24p video: When the output video resolution is set to Auto or Source Direct.

•720/24p video: When the output video resolution is set to Auto.

Note

•Even when 24p Direct Out is set to On, if a TV not compatible with 1080/24p video is connected, the actual frame frequency of the video output will be 60 Hz.

•The video output will be interrupted when switching the video output from 1080/24p or 720/24p to other output video resolutions, or when switching to 1080/24p or 720/24p from other output video resolutions.

Connecting using an S-Video output

You can use the S-Video output instead of the VIDEO OUT jack to connect this player to your TV (or other equipment).

•Use an S-Video cable (not supplied) to connect the S-VIDEO OUT to an S-Video input on your TV, monitor or AV receiver. Line up the small triangle above the jack with the same mark on the plug before plugging in.

					To S-video input
TV
CONTROL	IN
IR							AUDIO OUT	AUDIO OUT
	IN		Y				(5.1ch)	(2ch)
		VIDEO OUT				CENTER	SURROUND	FRONT
				DIGITAL AUDIO OUT			L	L
SETTING 2			PB
	HDMI OUT	LAN(100)
SETTING 1
IR RECEIVER		S	PR					R
			COMPONENT			SUB WOOFER	R
				COAXIAL	OPTICAL
			VIDEO OUT

14

En