Chapter

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Controls and displays

 

 

 

 

 

 

 

 

 

 

 

Front panel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

 

4

 

5

6

7

8

9

 

 

 

 

 

 

 

 

MCACC

 

 

 

 

 

HDMI iPod iPhone iPad

 

17

18

19

20

21

19

22

 

 

SPEAKERS DIMMER

DISPLAY BAND

TUNER EDIT

TUNE

PRESET

 

ENTER

 

 

 

 

 

 

 

 

 

 

 

AUTO SURROUND/

ALC/

ADVANCED

SOUND

iPod iPhone iPad

 

 

 

 

 

 

 

 

 

 

 

 

 

STREAM DIRECT STANDARD SURR

SURROUND

RETRIEVER AIR

DIRECT CONTROL

 

 

 

 

 

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

 

 

 

MASTER

 

 

 

 

 

 

SELECTOR

 

 

 

 

 

 

 

 

 

 

VOLUME

 

 

 

 

 

 

STANDBY/ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PHONES

 

 

 

USB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MCACC

VIDEO

 

 

 

 

 

23

24

25

26

27

28 27

29

 

 

 

 

SETUP MIC

 

iPad

 

 

 

 

 

 

 

 

 

 

iPod

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

iPhone

 

 

 

 

 

 

 

 

 

 

 

 

10

11

12

13

14

15 16

1

INPUT SELECTOR dial

 

 

 

 

5

Tuner control buttons

Selects an input source (page 25).

 

 

 

 

BAND – Switches between AM, FM ST (stereo) and FM

2

 

 

 

 

 

 

MCACC indicator

 

 

 

 

 

MONO radio bands (page 32).

Lights when Acoustic Calibration EQ (page 34) is on (Acoustic

 

TUNER EDIT – Use with TUNE /, PRESET / and

Calibration EQ is automatically set to on after the Auto

 

 

ENTER to memorize and name stations for recall

MCACC setup (page 23)).

 

 

 

 

 

(page 32).

3

Receiver control buttons

 

 

 

 

 

TUNE / – Used to find radio frequencies (page 32).

 

SPEAKERS – See Switching the speaker terminal on

 

 

PRESET / – Use to select preset radio stations

 

page 14.

 

 

 

 

 

(page 32).

 

DIMMER – Dims or brightens the display. The brightness

6

HDMI indicator

 

can be controlled in four steps.

 

 

 

Blinks when connecting an HDMI-equipped component;

 

DISPLAY – Switches the display of this unit. The listening

lights when the component is connected (page 17).

 

mode, sound volume, Speaker System (VSX-1022)/Pre Out

7

iPod iPhone iPad indicator

 

(VSX-822)setting or input name can be checked by

 

Lights when an iPod/iPhone/iPad is connected and iPod/USB

 

selecting an input source.

 

 

 

 

 

 

 

 

 

input is selected (page 27).

 

• The Speaker System/Pre Out setting may or may not be

 

8

Remote sensor

 

displayed, depending on the input source you have

 

 

 

Receives the signals from the remote control (see Operating

 

selected.

 

 

 

 

 

 

 

 

 

range of remote control on page 10).

4

Character display

 

 

 

 

 

 

 

 

9

MASTER VOLUME dial

See Display on page 8.

 

 

 

 

 

 

 

 

10

STANDBY/ON

 

 

 

 

 

 

11 PHONES jack

Use to connect headphones. When the headphones are connected, there is no sound output from the speakers. The listening mode when the sound is heard from the headphone can be selected only from PHONES SURR, STEREO or STEREO ALC mode (S.R AIR mode can be also selected with ADAPTER input).

12 Listening mode buttons

AUTO SURROUND/STREAM DIRECT – Switches between Auto surround mode (page 33) and Stream Direct playback (page 34).

ALC/STANDARD SURR – Press for standard decoding and to switch between the modes of 2Pro Logic II, 2 Pro Logic IIx, 2Pro Logic IIz and NEO:6, and the Auto level control stereo mode (page 33).

ADVANCED SURROUND – Switches between the various surround modes (page 34).

13 MCACC SETUP MIC jack

Use to connect a microphone when performing Auto MCACC setup (page 23).

7