3

 

 

 

 

 

 

 

 

 

 

 

 

Basic Setup

7

 

 

 

9

 

 

 

 

Wait for the test tones to finish.

 

Make sure ‘OK’ is selected, then press ENTER.

 

Other problems when using the Auto MCACC

 

A progress report is displayed on-screen while the

 

 

If the screen in step 8 is left untouched for 10 seconds

 

setup

 

receiver outputs test tones to determine the speakers

 

 

and ENTER is not pressed in step 9, the Auto MCACC

 

If the room environment is not optimal for the Auto MCACC

 

present in your setup. Try to be as quiet as possible while

 

 

setup will start automatically as shown.

 

 

 

 

 

setup (too much background noise, echo off the walls,

 

it’s doing this.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.Auto MCACC

 

obstacles blocking the speakers from the microphone) the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

final settings may be incorrect. Check for household

 

 

1.Auto MCACC

 

 

 

 

 

Now

Analyzing

 

 

 

 

 

 

 

 

 

appliances (air conditioner, fridge, fan, etc.), that may be

 

 

Now Analyzing

 

 

Surround

Analyzing

 

 

 

 

 

 

affecting the environment and switch them off if necessary. If

 

 

Environment

Check

 

 

Speaker

System

 

 

 

 

 

Speaker

Distance

 

there are any instructions showing in the front panel display,

 

 

Ambient Noise

 

 

Channel

Level

 

 

 

Speaker YES/NO

 

 

Acoustic

Cal EQ

 

please follow them.

 

 

 

 

 

 

 

 

 

 

 

Return

 

Some older TVs may interfere with the operation of the

 

 

 

 

 

Return

 

 

 

 

 

 

microphone. If this seems to be happening, switch off the

 

 

 

 

 

 

 

 

 

A progress report is displayed on-screen while the

 

TV when doing the Auto MCACC setup.

 

For correct speaker settings, do not adjust the volume

 

 

receiver outputs more test tones to determine the

 

 

 

 

during the test tones.

 

 

 

 

 

 

optimum receiver settings for channel level, speaker

 

 

 

 

 

 

 

 

 

 

 

distance, and Acoustic Calibration EQ.

 

 

 

Confirm the speaker configuration.

 

 

 

 

 

 

Again, try to be as quiet as possible while this is

 

 

8 The configuration shown on-screen should reflect the

 

 

 

 

 

 

happening. It may take 1 to 3 minutes.

 

 

 

actual speakers you have.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The Auto MCACC setup has finished! You return to the

 

 

 

 

1.Auto MCACC

 

 

 

10Home Menu.

 

 

 

 

 

 

Check!

 

 

The settings made in the Auto MCACC setup should give

 

 

 

 

Center

[

YES ]

 

 

you excellent surround sound from your system, but it is

 

 

 

 

Front

[

YES ]

 

 

also possible to adjust these settings manually using the

 

 

 

 

Surr

[

YES ]

 

 

 

 

 

 

Surr. Back

[YESx2]

 

 

Home Menu (starting on page 30).

 

 

 

 

Subwoofer

[

YES ]

 

 

 

 

 

 

 

 

 

 

 

 

Note

 

 

 

 

 

 

10:Next

 

 

OK

 

 

 

 

 

 

 

 

 

Return

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Depending on the characteristics of your room, sometimes

With error messages (such as Too much ambient

identical speakers with cone sizes of around 12 cm

noise) select RETRY after checking for ambient noise

(5 inches) will end up with different size settings. You can

(see Other problems when using the Auto MCACC

correct the setting manually using the Speaker Setting on

setup below).

page 30.

If the speaker configuration displayed isn’t correct, use

The subwoofer distance setting may be farther than the

/ to select the speaker and / to change the

actual distance from the listening position. This setting

setting. When you’re finished, go to the next step.

should be accurate (taking delay and room characteristics

If you see an error message (ERR) in the right side

into account) and generally does not need to be changed.

column, there may be a problem with the speaker

 

connection. If selecting RETRY doesn’t fix the problem,

 

turn off the power and check the speaker connections.

 

19