Pioneer VSX-9110TXV-K Using the tuner Chapter, Listening to the radio, Saving station presets

Using the tuner

Chapter 6:

Using the tuner

Listening to the radio

The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and manual (step) tuning functions. If you already know the frequency of the station you want, see Tuning directly to a station below. Once you are tuned to a station you can memorize the frequency for recall later—see Saving station presets on page 31 for more on how to do this.

SYSTEM OFF

RECEIVER	SELECTINPUT		SOURCE		DIALOG E	S.RETRIEVER		DTVON/OFF	REC	DTVINFO
				D.ACCESS			CLASS DISC				MUTE
AV PRE-PROGRAMMED AND LEARNING					+10			MPX		REC STOP	JUKEBOX
REMOTECONTROLUNIT							ENTER
				AVPARAMETER			CHLEVEL
				TOPMENU			MENU	AUDIO	SUBTITLE	HDD	DVD
					TUNE			DISP		CH	CH
				DTVMENU	ST	ST	T.EDIT	STATUS	SIGNAL SEL	SBch	STEREO
					ENTER
				SETUP			RETURN
CD		DVR 2			TUNE			MULTI OPE	THX	STANDARD	ADV.SURR
DVD	TV	DVR1	TVCTRL	GUIDE CATEGORY		BAND
					TV CONTROL			SHIFT	PHASE	MCACC	S.DIRECT
CD-R/TAPE	HDMI2	XM RADIO	ROOM 2
iPod	HDMI1	TUNER	RECEIVER	TVVOL	INPUT	TVCH	VOL
					SELECT

1Press the TUNER button to select the tuner.

2Use the BAND button to change the band (FM or AM), if necessary.

Each press switches the band between FM and AM.

3Tune to a station.

There are three ways to do this:

Automatic tuning

To search for stations in the currently selected band,

press and hold TUNE for about a second. The receiver will start searching for the next station, stopping when it has found one. Repeat to search for other stations.

Manual tuning

To change the frequency one step at a time, press

TUNE .

High speed tuning

Press and hold TUNE for high speed tuning. Release the button at the frequency you want.

Improving FM stereo sound

If the TUNED or STEREO indicators don't light when tuning to an FM station because the signal is weak, press the MPX button to switch the receiver into mono reception mode. This should improve the sound quality and allow you to enjoy the broadcast.

06

Tuning directly to a station

Sometimes, you'll already know the frequency of the station you want to listen to. In this case, you can simply enter the frequency directly using the number buttons on the remote control.

1Press the TUNER button to select the tuner.

2Use the BAND button to change the band (FM or AM), if necessary.

Each press switches the band between FM and AM.

3Press D.ACCESS (Direct Access).

4Use the number buttons to enter the frequency of the radio station.

For example, to tune to 106.00 (FM), press 1, 0, 6, 0, 0.

If you make a mistake halfway through, press D.ACCESS twice to cancel the frequency and start over.

Saving station presets

If you often listen to a particular radio station, it's convenient to have the receiver store the frequency for easy recall whenever you want to listen to that station. This saves the effort of manually tuning in each time. This receiver can memorize up to 30 stations, stored in three banks, or classes, (A, B and C) of 10 stations each. When saving an FM frequency, the MPX setting (see page 31) is also stored.

SYSTEM OFF

RECEIVER	SELECTINPUT		SOURCE		DIALOG E	S.RETRIEVER		DTVON/OFF	REC	DTVINFO
				D.ACCESS			CLASS DISC				MUTE
AV PRE-PROGRAMMED AND LEARNING					+10			MPX		REC STOP	JUKEBOX
REMOTECONTROLUNIT							ENTER
				AVPARAMETER			CHLEVEL
				TOPMENU			MENU	AUDIO	SUBTITLE	HDD	DVD
					TUNE			DISP		CH	CH
				DTVMENU	ST	ST	T.EDIT	STATUS	SIGNAL SEL	SBch	STEREO
					ENTER
				SETUP			RETURN
CD		DVR 2			TUNE			MULTI OPE	THX	STANDARD	ADV.SURR
						BAND
DVD	TV	DVR1	TVCTRL	GUIDE CATEGORY
					TV CONTROL			SHIFT	PHASE	MCACC	S.DIRECT
CD-R/TAPE	HDMI2	XM RADIO	ROOM 2
iPod	HDMI1	TUNER	RECEIVER	TVVOL	INPUT	TVCH	VOL
					SELECT

1 Tune to a station you want to memorize.

See Listening to the radio on page 31 for more on this.

2 Press T.EDIT (TUNER EDIT).

The display shows STATION MEMORY, then a blinking memory class.

3 Press CLASS to select one of the three classes then

press ST to select the station preset you want.

You can also use the number buttons to select a station preset.

4 Press ENTER.

After pressing ENTER, the preset class and number stop blinking and the receiver stores the station.

31

En