Manuals / Pitco Frialator / Kitchen Appliance / Pasta Maker

Pitco Frialator SSRS14, SSPG14 Plumbing Connections, Water Inlet Connections, Drain Connections

Models: SSPG14 SSRS14

1 28
Download 28 pages 5.55 Kb
Page 8
Image 8

INSTALLATION

1.4. PLUMBING CONNECTIONS

The plumbing installation should be done by a licensed plumber and must comply with local and national codes. The instructions for appliances connected to the water mains by detachable hose sets shall state that new hose sets will be used and that the old hose sets should not be reused (if applicable).

1.4.1.WATER INLET CONNECTIONS

If your appliance is equipped with a faucet or a water fill option connections to a potable water supply will be required. If a single water connection is required it is recommended that the appliance is connected to hot water supply. This will greatly decrease the time and energy required for the appliance to reach operating temperature. Prior to installation, a water treatment specialist should inspect the water supply. Water hardness should contain no more then 2.0 grains/gallon. The pH level should be between 6.5 and 8.0. These conditions can be obtained with the use of a properly maintained water softener. The incoming water pressure should be between 20 psi (138 kPa) to 60 psi (414 kPa). For higher water pressures, a high-pressure regulator must be installed to inlet plumbing to avoid damage caused by water hammer. The maximum allowable incoming water temperature is 180°F (82°C). Have your water tested and record the measured values below.

WARNING

When water is at a high temperature and high pressure, excessive splashing of hot water

may occur that could result in injury.

Water Quality Checklist

 

Measured

Max Limit or Range

OK

Temperature

 

180°F (82°C) Max.

 

Hardness

 

2.0 Grains/Gal. Max.

 

pH

 

6.5 to 8.0

 

Pressure

 

20 psi (138 kPa) to 60 psi (414 kPa)

 

1.4.2.DRAIN CONNECTIONS

Each tank has a drain that can be connected to a drainage system. Each tank also has an overflow line. The overflow connection is after the drain valve to provide an unobstructed overflow path. The tank drain and overflow line for each tank is connected together to form a common drain line.

When there are more than 2 appliances joined together the common drains can be connected together with a manifold that has a 1-1/4” NPT outlet connection. The outlet on the can be mounted so it can drain under the left or right hand unit.

4

L20-331, rev.02 (08/11)

Page 7 Page 9
Page 8
Image 8
Pitco Frialator SSRS14, SSPG14 operation manual Plumbing Connections, Water Inlet Connections, Drain Connections
Page 7 Page 9

SSPG14, SSRS14 specifications

The Pitco Frialator SSRS14 and SSPG14 are state-of-the-art commercial frying solutions designed for restaurants and food service establishments that prioritize efficiency, safety, and frying quality. These fryers are engineered to handle high-volume frying needs while delivering consistent results.

One of the standout features of the SSRS14 is its four-pan capability, allowing for a substantial amount of food to be fried simultaneously. This model is built for versatility, catering to various food items from crispy fries to perfectly fried chicken. The SSPG14, on the other hand, comes with a single fry pot but boasts a higher frying capacity, making it ideal for establishments that require flexibility without compromising on output.

Both models are equipped with advanced temperature control systems. The computerized control panel ensures precise temperature regulation, enhancing cooking efficiency and food quality. The oil management system is another highlight, which helps maintain optimal oil quality over longer periods. This not only reduces oil wastage but also improves the flavor profile of the fried products.

The fryers feature Pitco’s renowned frying oil filtration system, which extends the life of the oil. By efficiently removing food particles and other impurities, this technology contributes to both cost savings and enhanced food quality. Additionally, the SSRS14 and SSPG14’s stainless steel construction ensures durability and resistance to corrosion, promising longevity even in the face of heavy usage.

Safety is a top priority with both models. They come equipped with built-in safety features, including high-temperature limit switches that prevent overheating and potential hazards. The design also incorporates easy-access oil drainage systems for straightforward cleaning and maintenance, ensuring health standards are met effortlessly.

In terms of energy efficiency, the SSRS14 and SSPG14 utilize advanced heating technologies that require less energy while providing quick recovery times. This not only lowers operational costs but also contributes to a more sustainable kitchen environment.

In summary, the Pitco Frialator SSRS14 and SSPG14 are exceptional choices for food service operations looking to enhance their frying capabilities. Their combination of user-friendly features, advanced technology, and safety measures makes them indispensable assets for any commercial kitchen aiming to deliver high-quality fried foods consistently.