Manuals / Brands / Computer Equipment / Network Card / Planet Technology / Computer Equipment / Network Card

Planet Technology MAP-2105 3.2.2 Route, Apply, Domain Name, “Add” Button, Routing Table, “Apply” Button, Enable Static Routing, Secondary DNS Server IP Address

1 66

Download 66 pages, 3.09 Mb

Secondary DNS Server IP Address

Specify the IP address of the Secondary DNS server for this device. Leave blank when DHCPC is enabled, otherwise this entry will override the information obtained from DHCP server.

Domain Name

Specify the domain name.

Apply

Press this button to save new settings for Gateway IP Address, Primary and Secondary DNS Server IP Address, and Domain Name.

3.2.2 Route

Route contains the following:

Enable Static Routing

Check or uncheck the box to enable or disable static routing for this device.

“Apply” Button

Press this button to apply changes on Enable Static Routing.

Routing Table

Display the current active entry for this device.

“Add” Button

Press this button to add new entry to static routing. The following figure shows the page invoked after using “Add” Button

Contents

Mobile IP Roaming Gateway MAP-2105 Copyright Disclaimer FCC Compliance Statement CE mark Warning Trademarks Revision TABLE OF CONTENTS Page Chapter 1 Introduction 1.1Features 1.2Package Contents 1.3 Network Planning 1.4 Hardware Installation 1.5 Startup the MAP-2105 https://192.168.0.100 admin Chapter 2 Basic Network Setup Step 1: Gateway Configuration: Step 2: Reboot the Gateway Step 3: Relay Configuration: Step 4: Reboot the Relay Step 5: MAP-2105Configuration: Step 6: Reboot the MAP-2105 Step 7: Check MAP-2105status CN Info Client Info Chapter 3 Web Configuration Link Description 3.1 System Settings Device Name Device Location Contact Name Contact Email Contact Phone 3.2 Network 3.2.1 WAN --Static IP selected Netmask Apply Back Gateway IP Address 3.2.2 Route Subnet Gateway Device Comment Status 3.3 Local Service 3.3.1 MLRD 3.3.2 VPN Client 3.3.3 NTP 3.4 System Management 3.4.1 Password 3.4.2 SNMP SNMP version SNMPv2 Read only community Read/Write community SNMPv3 Read only username Read/Write username Secret password 3.4.3 Syslog Server 3.5 Tools 3.5.1 Ping 3.5.2 Download 3.5.3 Firmware Update 3.5.4 Settings Save Config Restore Config Install New Webserver Certificate From WAN Interface From VPN Interface 3.6 Reboot 3.7 Reset 3.8 Status 3.8.1 System 3.8.2 Interfaces Interface Hardware Address IP address 3.8.3 Services 3.8.4 MLRD 3.8.5 Route 3.8.6 Syslog Chapter 4 Management Utility 4.1 Installation and Un-installation 4.1.1 To install the MLRD Management Suite Page Page 4.1.2 To Uninstall the MLRD Management Suite 4.2How to use MLRD Management Suite 4.2.1 AP Finder 4.2.2 Trap Viewer Start info Clear 4.2.3 MLRD Manager Page 4.3 Node Configuration using MLRD Manager 4.3.1 File >Change SNMP Password 4.3.2 Status > System 4.3.3 Status > MLRD 4.3.4 Config > System 4.3.5 Config > Network > WAN DNS Domain Name Config > Network > WAN > Static Save and Enabled Static IP Config > Network > WAN > DHCP-Client Enable DHCP-Client 4.3.6 Config > Network > Route Gateway/Device Add Edit Delete 4.3.7 Config > Management > SNMP Password Set Access Config From Network Interface Set Trap Configurations SNMP Trap Version Destination IP Address 4.3.8 Config > Management > Access Control 4.3.9 Config > Management > Remote Syslog 4.3.10 Config > Services > NTP-Client 4.3.11 Config > Services > Mobile IP 4.3.12 Config > Services > VPN-Client Remote Network Subnet Remote Network Netmask Authentication Username Authentication Password Enable server-sideAuthentication 4.3.13 Commnad > Download/Upload 4.3.14 Command > Reboot 4.3.15 Command > Reset 4.3.16 Help > About