Manuals / Brands / Computer Equipment / Network Card / Planet Technology / Computer Equipment / Network Card

Planet Technology MAP-2105 Status, Netmask, IP Address, DNS Domain Name, Configure Details, Save and Enabled Static IP, Primary DNS Server IP Address, Secondary DNS Server IP Address

1 66

Download 66 pages, 3.09 Mb

Primary DNS Server IP Address

Specify the IP Address of the primary DNS Server for this device

Secondary DNS Server IP Address

Specify the IP Address of the secondary DNS server for this device

DNS Domain Name

Specify an optional domain name for the DNS client

Choose the desired Interface Type and hit the Configure Details button will lead to the configuration page for the specific interface type.

Config > Network > WAN > Static

Status

This is a read-only field that displays the status of the Static WAN IP Configuration. The Static WAN IP will be disabled if the DHCP-Client type is selected.

IP Address

The IP Address of the Static WAN IP Address

Netmask

The net mask corresponding to the Static WAN IP Address

Click on the Save and Enabled Static IP button to enable this type.

Config > Network > WAN > DHCP-Client

Contents

Mobile IP Roaming Gateway MAP-2105 Copyright Disclaimer FCC Compliance Statement CE mark Warning Trademarks Revision TABLE OF CONTENTS Page Chapter 1 Introduction 1.1Features 1.2Package Contents 1.3 Network Planning 1.4 Hardware Installation 1.5 Startup the MAP-2105 https://192.168.0.100 admin Chapter 2 Basic Network Setup Step 1: Gateway Configuration: Step 2: Reboot the Gateway Step 3: Relay Configuration: Step 4: Reboot the Relay Step 5: MAP-2105Configuration: Step 6: Reboot the MAP-2105 Step 7: Check MAP-2105status CN Info Client Info Chapter 3 Web Configuration Link Description 3.1 System Settings Device Name Device Location Contact Name Contact Email Contact Phone 3.2 Network 3.2.1 WAN --Static IP selected Netmask Apply Back Gateway IP Address 3.2.2 Route Subnet Gateway Device Comment Status 3.3 Local Service 3.3.1 MLRD 3.3.2 VPN Client 3.3.3 NTP 3.4 System Management 3.4.1 Password 3.4.2 SNMP SNMP version SNMPv2 Read only community Read/Write community SNMPv3 Read only username Read/Write username Secret password 3.4.3 Syslog Server 3.5 Tools 3.5.1 Ping 3.5.2 Download 3.5.3 Firmware Update 3.5.4 Settings Save Config Restore Config Install New Webserver Certificate From WAN Interface From VPN Interface 3.6 Reboot 3.7 Reset 3.8 Status 3.8.1 System 3.8.2 Interfaces Interface Hardware Address IP address 3.8.3 Services 3.8.4 MLRD 3.8.5 Route 3.8.6 Syslog Chapter 4 Management Utility 4.1 Installation and Un-installation 4.1.1 To install the MLRD Management Suite Page Page 4.1.2 To Uninstall the MLRD Management Suite 4.2How to use MLRD Management Suite 4.2.1 AP Finder 4.2.2 Trap Viewer Start info Clear 4.2.3 MLRD Manager Page 4.3 Node Configuration using MLRD Manager 4.3.1 File >Change SNMP Password 4.3.2 Status > System 4.3.3 Status > MLRD 4.3.4 Config > System 4.3.5 Config > Network > WAN DNS Domain Name Config > Network > WAN > Static Save and Enabled Static IP Config > Network > WAN > DHCP-Client Enable DHCP-Client 4.3.6 Config > Network > Route Gateway/Device Add Edit Delete 4.3.7 Config > Management > SNMP Password Set Access Config From Network Interface Set Trap Configurations SNMP Trap Version Destination IP Address 4.3.8 Config > Management > Access Control 4.3.9 Config > Management > Remote Syslog 4.3.10 Config > Services > NTP-Client 4.3.11 Config > Services > Mobile IP 4.3.12 Config > Services > VPN-Client Remote Network Subnet Remote Network Netmask Authentication Username Authentication Password Enable server-sideAuthentication 4.3.13 Commnad > Download/Upload 4.3.14 Command > Reboot 4.3.15 Command > Reset 4.3.16 Help > About