Manuals / Brands / Computer Equipment / Network Card / Planet Technology / Computer Equipment / Network Card

Planet Technology MAP-2105 4.3.13 Commnad > Download/Upload, 4.3.14 Command > Reboot, File Name, File Type, Operation Type, Server IP Address

1 66

Download 66 pages, 3.09 Mb

4.3.13 Commnad > Download/Upload

The MAP-2105 also provides the download and upload file feature. The following section describes the parameters of this pane

Server IP Address

Specifies the TFTP Server IP Address

File Name

Specifies the file name to be downloaded or uploaded

File Type

Select the file Type. The available options are Config file and Firmware image

Operation Type

Choose the type of operation to perform:

-Upload

-Download

-Download and Reboot

After enter the parameters, click on the OK button to start performing the command.

4.3.14 Command > Reboot

After configure the settings using MLRD Manager, the MAP-2105 must be rebooted before the settings take effect. However, beware that the reboot process would cause all the user who are currently connected to the network lose their connection until the unit has completely restart-up and resume.

Contents

Mobile IP Roaming Gateway MAP-2105 Copyright Disclaimer FCC Compliance Statement CE mark Warning Trademarks Revision TABLE OF CONTENTS Page Chapter 1 Introduction 1.1Features 1.2Package Contents 1.3 Network Planning 1.4 Hardware Installation 1.5 Startup the MAP-2105 https://192.168.0.100 admin Chapter 2 Basic Network Setup Step 1: Gateway Configuration: Step 2: Reboot the Gateway Step 3: Relay Configuration: Step 4: Reboot the Relay Step 5: MAP-2105Configuration: Step 6: Reboot the MAP-2105 Step 7: Check MAP-2105status CN Info Client Info Chapter 3 Web Configuration Link Description 3.1 System Settings Device Name Device Location Contact Name Contact Email Contact Phone 3.2 Network 3.2.1 WAN --Static IP selected Netmask Apply Back Gateway IP Address 3.2.2 Route Subnet Gateway Device Comment Status 3.3 Local Service 3.3.1 MLRD 3.3.2 VPN Client 3.3.3 NTP 3.4 System Management 3.4.1 Password 3.4.2 SNMP SNMP version SNMPv2 Read only community Read/Write community SNMPv3 Read only username Read/Write username Secret password 3.4.3 Syslog Server 3.5 Tools 3.5.1 Ping 3.5.2 Download 3.5.3 Firmware Update 3.5.4 Settings Save Config Restore Config Install New Webserver Certificate From WAN Interface From VPN Interface 3.6 Reboot 3.7 Reset 3.8 Status 3.8.1 System 3.8.2 Interfaces Interface Hardware Address IP address 3.8.3 Services 3.8.4 MLRD 3.8.5 Route 3.8.6 Syslog Chapter 4 Management Utility 4.1 Installation and Un-installation 4.1.1 To install the MLRD Management Suite Page Page 4.1.2 To Uninstall the MLRD Management Suite 4.2How to use MLRD Management Suite 4.2.1 AP Finder 4.2.2 Trap Viewer Start info Clear 4.2.3 MLRD Manager Page 4.3 Node Configuration using MLRD Manager 4.3.1 File >Change SNMP Password 4.3.2 Status > System 4.3.3 Status > MLRD 4.3.4 Config > System 4.3.5 Config > Network > WAN DNS Domain Name Config > Network > WAN > Static Save and Enabled Static IP Config > Network > WAN > DHCP-Client Enable DHCP-Client 4.3.6 Config > Network > Route Gateway/Device Add Edit Delete 4.3.7 Config > Management > SNMP Password Set Access Config From Network Interface Set Trap Configurations SNMP Trap Version Destination IP Address 4.3.8 Config > Management > Access Control 4.3.9 Config > Management > Remote Syslog 4.3.10 Config > Services > NTP-Client 4.3.11 Config > Services > Mobile IP 4.3.12 Config > Services > VPN-Client Remote Network Subnet Remote Network Netmask Authentication Username Authentication Password Enable server-sideAuthentication 4.3.13 Commnad > Download/Upload 4.3.14 Command > Reboot 4.3.15 Command > Reset 4.3.16 Help > About