Manuals / Brands / Computer Equipment / Switch / Planet Technology / Computer Equipment / Switch

Planet Technology WGSD-1020 Time:, Figure, Age-Out, 5.4.2.2Advanced:, Enable Delay Bound:, All High before Low:, Enable STP Protocol:, VLAN Operation Mode:, Enable IGMP Protocol:

1 93

Download 93 pages, 6.49 Mb

Figure 5-10WGSD-1020 Switch Advanced Settings Web Page screen

5.4.2.2Advanced:Enter the settings, then click Submit to apply the changes on this page.

MAC Table Address Entry Age-Out Time: type the number of seconds that an inactive MAC address remains in the Switch’s address table. The valid range is 300-765 seconds. The default value is 300 sec.

Max bridge transmit delay bound control: limit the packets queuing time in switch, if enable this function, the packets queued exceed will be drop. The valid value is 1 sec., 2 sec. and 4 sec. and off. Default value is 2 sec.

Broadcast Strom Filter mode: provide 5%, 10%, 15%, 20%, 25% and off for broadcast storm control activity.

Priority Queue Service:

First Come First Served: the sequence of packets sent is depend on arrive order.

All High before Low: the high priority packets sent before the low priority packets.

WRR (Weighted Round Robin): select the preference given to packets in the Switch’s high-priority queue. These options represent the number of high priority packets sent before one low priority packet. For example: High weight: 5 and Low weight 2. It means WGSD-1020 sends 5 high priority packets before sending 2 low priority packets.

Enable Delay Bound: limit the low priority packets queuing time in WGSD-1020. Default maximum delay time is 255 ms. If the low priority packet stays in Switch exceed Max delay time, it will be sent. The valid range is 1-255 ms.

QoS Policy: High Priority Levels: provide 0-7 priority levels can map to high or low queue.

Protocol Enable Setting

Enable STP Protocol: provide disable or enable STP protocol. Default mode is enabling.

Enable IGMP Protocol: provide disable or enable IGMP protocol. Default mode is enable.

VLAN Operation Mode: IEEE 802.1Q(Port-based) with GVRP VLAN mode. IEEE 802.Q( Port-based) without GVRP VLAN mode.

- 54 -

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning Revision TABLE OF CONTENTS Page 1. INTRODUCTION 1.1 Checklist 1.2 About the Switch 1.3Features Page 2. HARDWARE DESCRIPTION 2.1 Front Panel LED indicators: 2.2 Rear Panel 2.3 Hardware Installation Figure 3. End node or Hub or Switch connection Notice: Cable distance for Switch Make sure the wiring is correct 2.3.3 Connecting to Network Backbone or Server 3. SWITCH MANAGEMENT 3.1 Overview 3.2 Management Methods 3.2.1 Local Console Management 3.2.2 Remote Console Management 3.3Assigning an IP Address to the Switch 3.4 Logging on to the Switch 4. CONSOLE INTERFACE 4.1 CONNECT TO PC 4.2 Login in 4.3 Main screen 4.3.1 Status and Counters 4.3.1.2Port Counters 4.3.1.3System Information 4.3.2Switch Static Configuration Administration Configuration: Port & Trunking Configuration: Port Sniffer Configuration: VLAN Configuration: 4.3.2.1 Administration Configuration Device Information: IP Configuration: Change Username: Change Password: 4.3.2.1.2 IP Configuration “ctrl-A” 4.3.2.1.3Change Username “Edit” “save” 4.3.2.1.4Change Password Modify the password procedure: “Enter” 4.3.2.2 Port & Trunking Configuration ” Edit” 4.3.2.3 Port Sniffer Configuration ”Edit” Roving Analysis: Analysis Port: Monitor port: 4.3.2.4 VLAN Configuration VLAN Configure: Create a VLAN Group: Edit/ Delete a VLAN Group: 4.3.2.4.1 VLAN Configure 802.1Q with GVRP Port-based VLAN 4.3.2.4.2Create a VLAN Group Add a VLAN Group procedure: “ Edit” “Save” 4.3.2.4.3Edit / Delete VLAN Group 4.3.2.5 Priority Configuration High Low 4.3.2.6 MAC Address Configuration Static MAC Address: Filtering MAC Address: 4.3.2.6.1 Static MAC Address “Add” 4.3.2.6.2 Filtering MAC Address 4.3.2.7Misc Configuration Port Security: MAC Age Interval: Broadcast Storm Filtering: Max bridge transmits delay bound: please refer to chapter 4.3.2.7.2 MAC Age Interval 4.3.2.7.3 Broadcast Storm Filtering Broadcast Storm Filter setup procedure: Ctrl-A” “Action menu” 4.3.2.7.4Max Bridge Transmit Delay Bound 4.3.2.7.4.1 Max bridge transmit delay bound “OFF” 1, 2, or 4 sec Setup procedure: 4.3.2.7.4.2Enable Delay Bound Delay Bound 4.3.2.7.4.3 Max Delay Time 4.3.2.8Main Menu 4.3.3 Protocol Related Configuration STP Enable: System Configuration: Per port Configuration: 4.3.3.1.1 STP Enable 4.3.3.1.2System Configuration 4.3.3.1.3Per Port Configuration 4.3.3.2 SNMP System Options: Community Strings: Trap Managers: 4.3.3.2.1System Options 4.3.3.2.2Community Strings “add SNMP community” 4.3.3.2.3Trap Managers “Trap Managers” 4.3.3.2.4Previous Menu 4.3.3.3 GVRP Figure 4-62GVRP screen 4.3.3.4LACP Aggregator Settings: State Activity: LACP Status: 4.3.3.4.1 Aggregator Settings 4.3.3.4.2 State Activity passive “Active” 4.3.3.4.3LACP Status 4.3.3.4.4Previous Menu 4.3.3.5 Main Menu 4.3.4 Reboot Switch 4.3.4.2 Restart 4.3.4.3 Previous Menu 4.3.5 Command Line 4.3.6 Logout 5. WEB MANAGEMENT 5.1 Login in to the Switch 5.2 Port Status 5-3Port Statistics 5-4Administrator 5.4.1IP Address “Apply” “Reboot” ” Help” “Close” 5.4.2 Switch Settings 5.4.2.1Basic: Description: MAC address: Firmware version: 5.4.2.2Advanced: Enter the settings, then click Submit to apply the changes on this page MAC Table Address Entry Age-Out Time: Note: 5.4.3Console Port Information 5.4.4 Port Controls Speed: Duplex: 5.4.5Trunking 5.4.5.2Port aggregator status: Actor: Partner: Admin: Oper: Priority: 5.4.5.3State Activity Active( enable ): Passive ( not enable Active): Note: 5.4.6 Filter Database “administrator” “Filter Database” “static MAC Address” “add” Page MAC Filtering: 5.4.7 VLAN Configuration Page 5.4.7.2 Port VID “Port VID Settings” 2.Port VID( PVID): 3. Ingress Filtering: ingress filtering rule 5.4.7.3Port Based VLAN Create a new VLAN group and add member ports procedure: Page 5.4.8Spanning Tree Page Page 5.4.9 Port Sniffer 5.4.10 SNMP RO / Read Only: RW / Read Write: Trap Manager 5.4.11 Security Manager 5-5TFTP Update Firmware 5-6Configuration Backup TFTP Backup Configuration: 5-7Reset System 5-8Reboot System 5-9View the State, Link Activity and detail packet information 6. SWITCH OPERATION 6.1 Address Table 6.2 Learning 6.3 Forwarding & Filtering 6.4 Store-and-Forward 7.TROUBLESHOOTING APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45Pin Assignments A.2 10/100Mbps, 10/100Base-TX A.3 RJ-45cable pin assignment Page APPENDIX B TECHNICAL SPECIFICATIONS WGSD-102010/100/1000Mbps Intelligent Ethernet Switch