Manuals / Brands / Computer Equipment / Switch / Planet Technology / Computer Equipment / Switch

Planet Technology WGSD-1020 Figure, ” Help”, “Close”, 5.4.7.2 Port VID, 2.Port VID( PVID):, “Port VID Settings”, 3. Ingress Filtering:, ingress filtering rule, Ingress filtering rule 1:

1 93

Download 93 pages, 6.49 Mb

5.4.7.2 Port VID

In order for an end station send packets to different VLANs. Itself has to be either capable of tagging packets it sends with VLAN tags or attached to a VLAN-aware bridge that is capable of classifying and tagging the packet with different VLAN ID based on default PVID and other packet information.

Figure 5-29WGSD-1020 Port VID setting Web Page screen Please check the detail description of parameters as below:

1.From the main Tag-based (IEEE 802.1Q) VLAN page, click “Port VID Settings”.

2.Port VID( PVID):

Sets the port VLAN ID that will be assigned to untagged traffic on a given port. For example, if port 10’s default PVID is 100, all untagged packets on port 10 will belong to VLAN 100. The default setting for all port is VID 1. This feature is useful for accommodating device that you want to participate in the VLAN does not support VLAN tagging. Only one untagged VLAN is allowed per port.

3. Ingress Filtering:

Ingress filtering lets frames belonging to a specific VLAN to be forwarded if the port belongs to that VLAN.

Please note there are two ingress filtering rule as follows:

Ingress filtering rule 1: forward only packets with VID matching per port’s configured VID.

Ingress filtering rule 2: drop untagged frames.

You can click” Help” button; the following screen in Figure 5-28appears.

Click “Close” to close this screen.

- 68 -

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning Revision TABLE OF CONTENTS Page 1. INTRODUCTION 1.1 Checklist 1.2 About the Switch 1.3Features Page 2. HARDWARE DESCRIPTION 2.1 Front Panel LED indicators: 2.2 Rear Panel 2.3 Hardware Installation Figure 3. End node or Hub or Switch connection Notice: Cable distance for Switch Make sure the wiring is correct 2.3.3 Connecting to Network Backbone or Server 3. SWITCH MANAGEMENT 3.1 Overview 3.2 Management Methods 3.2.1 Local Console Management 3.2.2 Remote Console Management 3.3Assigning an IP Address to the Switch 3.4 Logging on to the Switch 4. CONSOLE INTERFACE 4.1 CONNECT TO PC 4.2 Login in 4.3 Main screen 4.3.1 Status and Counters 4.3.1.2Port Counters 4.3.1.3System Information 4.3.2Switch Static Configuration Administration Configuration: Port & Trunking Configuration: Port Sniffer Configuration: VLAN Configuration: 4.3.2.1 Administration Configuration Device Information: IP Configuration: Change Username: Change Password: 4.3.2.1.2 IP Configuration “ctrl-A” 4.3.2.1.3Change Username “Edit” “save” 4.3.2.1.4Change Password Modify the password procedure: “Enter” 4.3.2.2 Port & Trunking Configuration ” Edit” 4.3.2.3 Port Sniffer Configuration ”Edit” Roving Analysis: Analysis Port: Monitor port: 4.3.2.4 VLAN Configuration VLAN Configure: Create a VLAN Group: Edit/ Delete a VLAN Group: 4.3.2.4.1 VLAN Configure 802.1Q with GVRP Port-based VLAN 4.3.2.4.2Create a VLAN Group Add a VLAN Group procedure: “ Edit” “Save” 4.3.2.4.3Edit / Delete VLAN Group 4.3.2.5 Priority Configuration High Low 4.3.2.6 MAC Address Configuration Static MAC Address: Filtering MAC Address: 4.3.2.6.1 Static MAC Address “Add” 4.3.2.6.2 Filtering MAC Address 4.3.2.7Misc Configuration Port Security: MAC Age Interval: Broadcast Storm Filtering: Max bridge transmits delay bound: please refer to chapter 4.3.2.7.2 MAC Age Interval 4.3.2.7.3 Broadcast Storm Filtering Broadcast Storm Filter setup procedure: Ctrl-A” “Action menu” 4.3.2.7.4Max Bridge Transmit Delay Bound 4.3.2.7.4.1 Max bridge transmit delay bound “OFF” 1, 2, or 4 sec Setup procedure: 4.3.2.7.4.2Enable Delay Bound Delay Bound 4.3.2.7.4.3 Max Delay Time 4.3.2.8Main Menu 4.3.3 Protocol Related Configuration STP Enable: System Configuration: Per port Configuration: 4.3.3.1.1 STP Enable 4.3.3.1.2System Configuration 4.3.3.1.3Per Port Configuration 4.3.3.2 SNMP System Options: Community Strings: Trap Managers: 4.3.3.2.1System Options 4.3.3.2.2Community Strings “add SNMP community” 4.3.3.2.3Trap Managers “Trap Managers” 4.3.3.2.4Previous Menu 4.3.3.3 GVRP Figure 4-62GVRP screen 4.3.3.4LACP Aggregator Settings: State Activity: LACP Status: 4.3.3.4.1 Aggregator Settings 4.3.3.4.2 State Activity passive “Active” 4.3.3.4.3LACP Status 4.3.3.4.4Previous Menu 4.3.3.5 Main Menu 4.3.4 Reboot Switch 4.3.4.2 Restart 4.3.4.3 Previous Menu 4.3.5 Command Line 4.3.6 Logout 5. WEB MANAGEMENT 5.1 Login in to the Switch 5.2 Port Status 5-3Port Statistics 5-4Administrator 5.4.1IP Address “Apply” “Reboot” ” Help” “Close” 5.4.2 Switch Settings 5.4.2.1Basic: Description: MAC address: Firmware version: 5.4.2.2Advanced: Enter the settings, then click Submit to apply the changes on this page MAC Table Address Entry Age-Out Time: Note: 5.4.3Console Port Information 5.4.4 Port Controls Speed: Duplex: 5.4.5Trunking 5.4.5.2Port aggregator status: Actor: Partner: Admin: Oper: Priority: 5.4.5.3State Activity Active( enable ): Passive ( not enable Active): Note: 5.4.6 Filter Database “administrator” “Filter Database” “static MAC Address” “add” Page MAC Filtering: 5.4.7 VLAN Configuration Page 5.4.7.2 Port VID “Port VID Settings” 2.Port VID( PVID): 3. Ingress Filtering: ingress filtering rule 5.4.7.3Port Based VLAN Create a new VLAN group and add member ports procedure: Page 5.4.8Spanning Tree Page Page 5.4.9 Port Sniffer 5.4.10 SNMP RO / Read Only: RW / Read Write: Trap Manager 5.4.11 Security Manager 5-5TFTP Update Firmware 5-6Configuration Backup TFTP Backup Configuration: 5-7Reset System 5-8Reboot System 5-9View the State, Link Activity and detail packet information 6. SWITCH OPERATION 6.1 Address Table 6.2 Learning 6.3 Forwarding & Filtering 6.4 Store-and-Forward 7.TROUBLESHOOTING APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45Pin Assignments A.2 10/100Mbps, 10/100Base-TX A.3 RJ-45cable pin assignment Page APPENDIX B TECHNICAL SPECIFICATIONS WGSD-102010/100/1000Mbps Intelligent Ethernet Switch