Mount the new lamp cartridge | PLUS Vision U5-732 instruction

Replacing the Lamp Cartridge

5 Mount the new lamp cartridge.

(1)Push the lamp cartridge in slowly.

(Line it up with the screw holes in the projector.)

(2)Turn the lamp cartridge screw clockwise to tighten them.

6 Mount the lamp cover.

(1)Set the tip of the lamp cover in place, then close the lamp cover.

(2) Turn the lamp cover’s screw clockwise to tighten it.

7 Reset the Lamp Timer.

Connect the power cable, switch on the power, and then reset.

Select [Info.] → [Lamp Timer Reset] on the menu and press the ENTER button. There is a change to the initialization verification display. Press the ENTER button again. See “Lamp Timer Reset” on Page E-59.

Note:

After reaching the lamp service life, if the lamp is used for more than another 100 hours, it will not be possible to switch on the power. Should this happen, while the projector is in the standby mode, simultaneously holding down the projector’s SOURCE button and AUTO button for more than 5 seconds will clear the lamp timer. Checking that the STATUS indicator is out will show that the lamp timer has been cleared.

Contact a store that sells the U5-732 for a replacement lamp. Indicate you need a U5-200 replacement lamp for the U5-732 (order code 28-050).

E-66

Image 66

PLUS Vision U5-732 user manual Mount the new lamp cartridge, Mount the lamp cover, Reset the Lamp Timer

Contents

U5-732 DOC Compliance Notice PrecautionsThis label is located on the side of the remote control Do not look at the laser pointer’s light source Cleaning InstallationPower Supply Lamp Replacement Major Features Table of Contents Table of Contents Checking the Supplied Accessories Power cable 1.8 m / 5.9 feetUSB cable type A, 2 m / 6.6 feet Checking the Supplied Accessories Storage case for projector and accessoriesVelcro strap Pocket Cable storage pouch Names of the Main Unit Parts Zoom ring E-26 Built-in Security Slot Names of the Main Unit Parts Names of Parts/Preparing the Remote Control Unit Names of the Remote Control Parts Inserting the Batteries Side View Remote Control RangeRemote control sensor 5m/16.4feet 6m/19.7feet Procedure Up to Projecting to the Screen Placement Guide Screen Size and Projection Distance Placement Guide Lens center Personal computer RGB signal cable Supplied item Connections with Personal Computer To Output the External Output Signal of a Notebook Computer Connecting Personal Computers and Video EquipmentManufacturer Model Key Video Equipment with S-VIDEO Connectors Connections with Composite SignalsVideo Equipment with Video Connectors → Video See Input Format on Page E-56 Green Blue Red Cb Cr Connections with Component SignalsComponent cable Available as an option Order code Pb Pr Green Blue Red Connections with the Audio Jack Audio cable Supplied item Audio conversion adapter RedAudio cable Supplied item Switch on the projector power Operating This completes the selection of the display language Power Cable Connections and Switching the Power On/OffPress the Enter button to set Cursor Unplug the power cable FinishingStandby button on main unit Adjust the projection image to the screen Adjustment of the Projection ScreenAdjustment of the Projection Screen Zoom ring Focus ring Making Adjustments with the AdjustersAdjuster button Raising the projection image General Operation When Auto Source is OnWhen Auto Source is Off Input Selection Automatic Adjustment Press of the Auto button starts the automatic adjustmentGeneral Operation Cancelling Video and Audio Temporarily Freezing a Moving Picture Adjustment of the Volume Enlargement of the Image and Video Movement Image can also be moved in the following circumstancesPress the Zoom button to enlarge the image Using the Presentation Timer Using the Laser Pointer Operation JOG buttons Connecting the computer and projectorClick button on back Click button Controlling the Projector from a Computer Serial cable D-Sub 9-pin, straight commercially available Protecting the Projector with the Security Lock Canceling the password Input the password using the number buttons 1 toCanceling the password/Changing the password Changing the password Using the Quick Menu Content of Adjustments and SettingsVolume Select buttons Menu Operation MethodMenu button Enter button Menu Screen Names and Functions Adjustment Bar and Settings ContentsAdjustment Bar Menu Operation Method Performing Menu Operations Menu Display Press the Menu button to display the menu Making Adjustments/Settings This condition al- lows selection of the item nameSub menu Selecting Another Menu Name with Remote Control Operation Color View Option Menu name Item Name Sub Menu SetupVideo Info Brightness / Contrast / Color / Tint / Sharpness Picture Adj. Picture AdjustmentImage Picture Adj. / Fine Picture / H Position / V Position Fine Picture ResetPress of the Enter button forces the reset Position Quick Color Adj Select the preset color modeColor Gamma White Selection contents at the time of YPbPr inputColor Temp Color Space White Balance View Personal Computer SignalVideo Signals Aspect Keystone Save Vertical Flip / Horizontal FlipKeystone View Setup Auto Power OffAuto Source Status Indicator Lamp ModeSetup Menu Position Input Format Presentation TimerTo start the timer Video and S-Video On Screen OptionLanguage Background Startup Screen Security LockOption Info Factory DefaultLamp Timer Reset Status Resolution / Frequency Lamp TimerInfo When an Indicator is Lit or Flashing Thermal Protector Troubleshooting Check the following matters before requesting servicing Cleaning the Inside of the Projector CleaningCleaning a Soiled Projector Main Unit Dirty Lens Replacing the Lamp Cartridge Replacing the Lamp Cartridge Remove the lamp cartridge Reset the Lamp Timer Mount the new lamp cartridgeMount the lamp cover Electrical SpecificationsOptical Mechanical Table of Supported Frequency SignalResolution Frequency Video On Apple Macintosh Cabinet Dimensions 260 216 Unit mm inch 2005