KEY Part Description | Poulan 421064 instruction

REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001802)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1175321X479 IMPELLER

2196710 GEARBOX ASSEMBLY

3	188909	BEARING
4	191079	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X008 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4−20
10	74780426	SCREW 1/4−20 X .625
11	155377	NUT 5/16−18

12163183 SCREW 5/16−18 X .625

1319111507 WASHER

1410040500 LOCKWASHER 5/16

1574940516 SCREW 5/16−18 X 1.00

16180355 CARRIAGE BOLT

17194189 SCREW 13−16 X .625

18	407760	PLUG
19	407761	GEARBOX COVER RH
20	407766	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	407757	IMPELLER SHAFT
30	7836M	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O−RING

35407767 SCREW 5/16−18 X .750

36407765 GEARBOX COVER LH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

21

Image 21

Poulan 421064 owner manual KEY Part Description

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper Handle Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEY Recoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Cleaning Snow ThrowerEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingAuger Bearing Bearing Plug Auger Assembly 30 RH Auger Assembly 30 LH Chute Weldment Deflector Control AssemblyDeflector Weldment Deflector Seal Rotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley Pivot Loop Handle LH 419798X479 Knob RED SpacerHandle Knob Washer 3/8 Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD Bottom Lower Handle Wire HarnessPivot Support Weldment Console Panel Repair Parts Snow Thrower Model PP10530ES Drive END Plate 43 420900 Drive Plate AssemblyWasher Control ARM 01.03.002-A KEY Part Description Tecumseh Engine Model LH358SA-159628A417014X428 Engine Mount Plate Belt Cover Traction BeltImpeller Belt Wheel Driver Retainer Ring CoverWheel Lobe Clutch Slide Cable Bracket RH Cable Bracket LH 35062 Safety Ignition KEY DECAL, Danger 181037 Service Notes HOP Limited Warranty