Manuals / Poulan / Lawn and Garden / Snow Blower

Poulan 421064 owner manual Auger Housing, Scrapper BAR, Auger Bearing, Bearing Plug

Models: 421064

1 40

Download 40 pages 10.63 Kb

Page 22

Image 22

REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001802)

AUGER HOUSING / IMPELLER ASSEMBLY

	3 (5x)
	4 (5x)	KEY	PART
		KEY	PART	DESCRIPTION
2		NO.	NO.	DESCRIPTION
2		1	404930X428	AUGER HOUSING
		1	404930X428	AUGER HOUSING
		2	404933X479	SCRAPPER BAR
		3	72270505	CARRIAGE BOLT 5/16−18 X .625
	01.07.003-A	4	155377	NUT 5/16−18
	01.07.003-A

2	3

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
3	1	420478	AUGER BEARING
3	2	411939	BEARING PLUG
01.07.024-B	2	411939	BEARING PLUG
01.07.024-B	3	179582	SCREW 5/16−18 X 1.00

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 22

Image 22

Poulan 421064 owner manual Auger Housing, Scrapper BAR, Auger Bearing, Bearing Plug

Contents

Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine ADD Gasoline See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationSnow Thrower CleaningEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Exploded KEY Part Description Auger Bearing Auger HousingScrapper BAR Bearing PlugAuger Assembly 30 LH Auger Assembly 30 RHDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealRotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley Pivot419798X479 Loop Handle LHHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomPivot Support Weldment Wire HarnessLower Handle Console PanelRepair Parts Snow Thrower Model PP10530ES Drive Washer 43 420900 Drive Plate AssemblyEND Plate Control ARM01.03.002-A LH358SA-159628A KEY Part Description Tecumseh Engine Model417014X428 Engine Mount Plate Traction Belt Belt CoverImpeller Belt Wheel Lobe CoverWheel Driver Retainer Ring Clutch SlideCable Bracket LH Cable Bracket RHSafety Ignition KEY 35062181037 DECAL, DangerService Notes Limited Warranty HOP

KEY

AUGER HOUSING

SCRAPPER BAR

KEY

AUGER BEARING

BEARING PLUG