LEVER/CABLE Rotator Assembly, Rotator Head

REPAIR PARTS SNOW THROWER - MODEL PR1030ES (96192003100)

CONTROL PANEL / DISCHARGE CHUTE

KEY	PART	*6
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	428272	LEVER/CABLE ROTATOR ASSEMBLY
2	17501010	SCREW 10-24 X .625	*4
*3	420678	ROTATOR HEAD	*4	01.09.010-A	*5
*4	405932	ROTATOR PIVOT BRACKET		01.09.010-A	*5
*4	405932	ROTATOR PIVOT BRACKET
*5	420675	PULLEY PIVOT
*6	428273	CABLE ASSEMBLY ADJUSTABLE
*7	428310	CABLE ASSEMBLY HEAT SHIELD

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

101.15.009-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	421249	STEER CABLE
2	74041024	SCREW 10−24 X 1.50

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 26

Image 26

Poulan 428556 LEVER/CABLE Rotator Assembly, Rotator Head, Rotator Pivot Bracket, Pulley Pivot, Cable Assembly Adjustable

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Check Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engine HOW to USE Your Snow Thrower Stopping To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Engine CleaningSnow Thrower Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH KEY Part Description 23 22 Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller Pulley Auger Bearing Bearing Plug Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot Bracket Repair Parts Snow Thrower Model PR1030ES Handles Knob RED Repair Parts HandlesSpacer Handle Knob Shifter ROD TOP Impeller RODTraction ROD Shifter ROD Bottom Pivot Support Wire HarnessLower Tube Console Panel Sprocket Repair Parts Snow Thrower Model PR1030ES DriveAxle Shaft Repair Parts Snow Thrower Model PR1030ES 96192003100DRIVE Speed Selector AssemblyDrive Plate Assembly Rubber Ring Frame Cover AssemblyComplete LCT Engine 427963X428 Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley Repair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket LH Cable Bracket RH 422663 Repair Parts Snow Thrower Model PR1030ES BAG of PartsSafety Ignition KEY DECAL, Danger Repair Parts Snow Thrower Model PR1030ES Decals181037 DECAL, DANGER, Deflector Limited Warranty HOP

KEY

LEVER/CABLE ROTATOR ASSEMBLY

ROTATOR HEAD

ROTATOR PIVOT BRACKET

PULLEY PIVOT

CABLE ASSEMBLY ADJUSTABLE

KEY

STEER CABLE