Complete LCT Engine, Frame, 427963X428

REPAIR PARTS SNOW THROWER - MODEL PR1030ES (96192003100)

CHASSIS / ENGINE / PULLEYS

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	- -	428173	COMPLETE LCT ENGINE
01.00.034-A	1	418694X428	FRAME
01.00.034-A	2	150406	BOLT 3/8-16
	2	150406	BOLT 3/8-16
	3	428867	SCREW 5/16-18 X .750

1	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	427963X428	ENGINE MOUNTING PLATE

01.01.004-A

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	418601	COVER ASSEMBLY
2	2	17490408	SCREW 1/4-20 X .50
2

01.21.014-B 2

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 34

Image 34

Poulan 428556 owner manual Complete LCT Engine, Frame, 427963X428, Engine Mounting Plate, Cover Assembly

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engine HOW to USE Your Snow Thrower Stopping Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Snow Thrower CleaningEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH KEY Part Description 23 22 Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller Pulley Auger Bearing Bearing Plug Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot Bracket Repair Parts Snow Thrower Model PR1030ES Handles Knob RED Repair Parts HandlesSpacer Handle Knob Shifter ROD TOP Impeller RODTraction ROD Shifter ROD Bottom Pivot Support Wire HarnessLower Tube Console Panel Axle Shaft Repair Parts Snow Thrower Model PR1030ES DriveSprocket Repair Parts Snow Thrower Model PR1030ES 96192003100DRIVE Speed Selector AssemblyDrive Plate Assembly Rubber Ring Frame Cover AssemblyComplete LCT Engine 427963X428 Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley Repair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket LH Cable Bracket RH Safety Ignition KEY Repair Parts Snow Thrower Model PR1030ES BAG of Parts422663 DECAL, Danger Repair Parts Snow Thrower Model PR1030ES Decals181037 DECAL, DANGER, Deflector Limited Warranty HOP

Poulan 428556 Complete LCT Engine, Frame, 427963X428, Engine Mounting Plate, Cover Assembly

Models: 428556

KEY

COMPLETE LCT ENGINE

FRAME

KEY

427963X428

ENGINE MOUNTING PLATE

01.01.004-A

KEY

COVER ASSEMBLY