To Remove Wheels See Fig, Carburetor, Engine Speed | Poulan 428556

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 23)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL	OUTER HOLE
IN OUTER HOLE
OF AXLE ONLY)

AXLE

WHEEL

WHEEL HUB

FIG. 23

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 24)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 24

18

Image 18

Poulan 428556 owner manual To Remove Wheels See Fig, Carburetor, Engine Speed, To Adjust Cable Tension See Fig

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engine HOW to USE Your Snow Thrower Stopping Using the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Snow ThrowerEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH KEY Part Description 23 22 Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller Pulley Auger Bearing Bearing Plug Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot Bracket Repair Parts Snow Thrower Model PR1030ES Handles Knob RED Repair Parts HandlesSpacer Handle Knob Shifter ROD TOP Impeller RODTraction ROD Shifter ROD Bottom Pivot Support Wire HarnessLower Tube Console Panel Repair Parts Snow Thrower Model PR1030ES Drive Axle ShaftSprocket Repair Parts Snow Thrower Model PR1030ES 96192003100DRIVE Speed Selector AssemblyDrive Plate Assembly Rubber Ring Frame Cover AssemblyComplete LCT Engine 427963X428 Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley Repair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower Model PR1030ES BAG of Parts Safety Ignition KEY422663 DECAL, Danger Repair Parts Snow Thrower Model PR1030ES Decals181037 DECAL, DANGER, Deflector Limited Warranty HOP