Install Traction Drive Control ROD See Figs | Poulan 428556 instruction

ASSEMBLY / PRE-OPERATION

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.

1.Remove plastic tie securing rod to lower handle.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

PLASTIC TIE

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1.Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end.

2.Hook end of spring into control arm with loop opening up as shown. (See Fig. 5)

3.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

VINYL

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

6

Image 6

Poulan 428556 owner manual Install Traction Drive Control ROD See Figs, Install Auger Control ROD See Figs

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engine HOW to USE Your Snow Thrower Stopping Using the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Snow ThrowerEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH KEY Part Description 23 22 Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller Pulley Auger Bearing Bearing Plug Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot Bracket Repair Parts Snow Thrower Model PR1030ES Handles Knob RED Repair Parts HandlesSpacer Handle Knob Shifter ROD TOP Impeller RODTraction ROD Shifter ROD Bottom Pivot Support Wire HarnessLower Tube Console Panel Repair Parts Snow Thrower Model PR1030ES Drive Axle ShaftSprocket Repair Parts Snow Thrower Model PR1030ES 96192003100DRIVE Speed Selector AssemblyDrive Plate Assembly Rubber Ring Frame Cover AssemblyComplete LCT Engine 427963X428 Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley Repair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower Model PR1030ES BAG of Parts Safety Ignition KEY422663 DECAL, Danger Repair Parts Snow Thrower Model PR1030ES Decals181037 DECAL, DANGER, Deflector Limited Warranty HOP