Cable Bracket LH, Cable Bracket RH | Poulan 428556 specification

REPAIR PARTS SNOW THROWER - MODEL PR1030ES (96192003100)

WHEELS

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	192092X421	WHEEL 16 X 4.80 X LH
2	192093X421	WHEEL 16 X 4.80 X RH

1

2

01.06.005-A

1

2

01.15.003-A

		KEY	PART	DESCRIPTION
		NO.	NO.	DESCRIPTION
	3	1	410293	CABLE BRACKET LH
	3	2	410294	CABLE BRACKET RH
		2	410294	CABLE BRACKET RH
		3	17060410	SCREW 1/4−20 X .625

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

37

Image 37

Poulan 428556 owner manual Cable Bracket LH, Cable Bracket RH

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper Handle Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Install Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEY Recoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Snow Thrower CleaningEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting Auger Assembly 30 LH Auger HousingAuger Assembly 30 RH KEY Part Description 23 22 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller Pulley Bearing Plug Auger Bearing Chute Weldment Deflector Control AssemblyDeflector Weldment Deflector Seal Cable Assembly Adjustable LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot Bracket Repair Parts Snow Thrower Model PR1030ES Handles Spacer Repair Parts HandlesKnob RED Handle Knob Traction ROD Impeller RODShifter ROD TOP Shifter ROD Bottom Lower Tube Wire HarnessPivot Support Console Panel Axle Shaft Repair Parts Snow Thrower Model PR1030ES DriveSprocket Repair Parts Snow Thrower Model PR1030ES 96192003100DRIVE Drive Plate Assembly AssemblySpeed Selector Rubber Ring Complete LCT Engine Cover AssemblyFrame 427963X428 Traction Belt Impeller BeltIdler ARM Bracket Idler Pulley Repair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket RH Cable Bracket LH Safety Ignition KEY Repair Parts Snow Thrower Model PR1030ES BAG of Parts422663 181037 Repair Parts Snow Thrower Model PR1030ES DecalsDECAL, Danger DECAL, DANGER, Deflector HOP Limited Warranty