Lower Handle, Pivot Support Weldment | Poulan 436134, 96192004300

REPAIR PARTS SNOW THROWER - - MODEL NO. PR827ES (96192004300)

HANDLES

	KEY	PART
	NO.	NO.	DESCRIPTION
2	1	419797X431	LOWER HANDLE
2	2	427513X431	PIVOT SUPPORT WELDMENT
	2	427513X431	PIVOT SUPPORT WELDMENT
	3	428867	SCREW 5/16−18 X .750
	4	17000616	SCREW 3/8−16 X 1.00
	3

01-05-013-A

			KEY	PART
			NO.	NO.	DESCRIPTION
4	4		1	419798X431	LOOP HANDLE LH
4			2	419799X431	LOOP HANDLE RH
4			3	74780524	SCREW 5/16−18 X 1.50
		1	3	74780524	SCREW 5/16−18 X 1.50
		1	4	751153	NUT 5/16−18
			4	751153	NUT 5/16−18
3
4
3
2

01.08.004-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 28

Page 28

Image 28

Poulan 436134 Repair Parts Snow Thrower - Model NO. PR827ES Handles, Lower Handle, Pivot Support Weldment, Loop Handle LH

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Operation Know Your Snow ThrowerPrimer Traction Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See Fig To Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See Fig Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine Speed Storage OtherFuel System Engine OIL Troubleshooting Service Notes Auger Housing KEY Part DescriptionScraper BAR Auger Bearing Auger 27 LH Auger 27 RHSkid Plate LH Skid Plate RH Exploded Gearbox Assembly 178675X431 Corner Bracket Clean OUT ToolBearing Impeller Pulley Deflector Control Assembly Chute WeldmentDeflector Weldment Deflector Seal LEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator Head Repair Parts Snow Thrower - Model NO. PR827ES Handles Lower HandlePivot Support Weldment Loop Handle LH Wire Harness Console PanelHeadlight Bezel Flood Headlight Spacer Knob REDHandle Knob Washer 3/8 Impeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD Bottom Repair Parts Snow Thrower - Model NO. PR827ES Drive Assembly Drive Plate AssemblySpeed Selector Rubber Ring Axle Shaft Roll PIN 3/16Sprocket Clik PIN Engine Model 12A114 Frame436146X421 Engine Mount Plate Impeller Belt Traction BeltIdler ARM Bracket Idler Pulley Repair Parts Snow Thrower - Model NO. PR827ES Wheels Wheel Assembly LH432335X428 432336X428 Safety Ignition KEY Repair Parts Snow Thrower - Model NO. PR827ES BAG of Parts193071 435840 Shifter ROD TOP Shifter ROD BottomKIT Harness Conn B&S Repair Parts Snow Thrower - Model NO. PR827ES Decals 181037DECAL, Danger DECAL, DANGER, Deflector Service Notes Service Notes Service Notes Limited Warranty

Poulan 436134 Repair Parts Snow Thrower - Model NO. PR827ES Handles, Lower Handle, Loop Handle LH

Models: 96192004300 436134

REPAIR PARTS SNOW THROWER - - MODEL NO. PR827ES (96192004300)

HANDLES

KEY

LOWER HANDLE

PIVOT SUPPORT WELDMENT

KEY

LOOP HANDLE LH

LOOP HANDLE RH