Meets A.N.S.I. Safety Requirements | Poulan 96192004300, 436134

OPERATION

GASOLINE

FILLER CAP

MUFFLER

CHOKE CON-

TROL

PRIMER

SAFETY

IGNITION

KEYON / OFF SWITCH

		DISCHARGE CHUTE
ELECTRIC	AUGER	DRIVE CONTROL LEVER
START BUTTON	CONTROL	SPEED
RECOIL	LEVER	CONTROL	DEFLECTOR REMOTE
RECOIL		LEVER	CONTROL LEVER
(AUXILIARY)
STARTER			TRACTION
HANDLE			TRACTION
	CHUTE		DRIVE
	CHUTE		CONTROL
DEFLECTOR			LEVER

DISCHARGE

CHUTE

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE ENGINE. ACTUAL LOCATION MAY VARY WITH THE ENGINE ON YOUR UNIT.

AUGERS

CLEAN-OUT TOOL

FIG. 10

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke control - used for starting a cold engine. ON / OFF switch - used to STOP the engine.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power- propelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the direc- tion the snow is thrown.

Deflector remote control lever - used to change the distance the snow is thrown.

Skid plate - used to adjust height of scraper bar from the

9 ground.

Image 9

Poulan 96192004300 Meets A.N.S.I. Safety Requirements, Recoil auxiliary starter handle used for starting the engine

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Traction Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See Fig Using the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen Maintenance Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting Service Notes KEY Part Description Auger HousingScraper BAR Auger Bearing Auger 27 RH Auger 27 LHSkid Plate LH Skid Plate RH Exploded 178675X431 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller Pulley Chute Weldment Deflector Control AssemblyDeflector Weldment Deflector Seal Cable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator Head Lower Handle Repair Parts Snow Thrower - Model NO. PR827ES HandlesPivot Support Weldment Loop Handle LH Console Panel Wire HarnessHeadlight Bezel Flood Headlight Knob RED SpacerHandle Knob Washer 3/8 Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD Bottom Repair Parts Snow Thrower - Model NO. PR827ES Drive Drive Plate Assembly AssemblySpeed Selector Rubber Ring Roll PIN 3/16 Axle ShaftSprocket Clik PIN Frame Engine Model 12A114436146X421 Engine Mount Plate Traction Belt Impeller BeltIdler ARM Bracket Idler Pulley Wheel Assembly LH Repair Parts Snow Thrower - Model NO. PR827ES Wheels432335X428 432336X428 Repair Parts Snow Thrower - Model NO. PR827ES BAG of Parts Safety Ignition KEY193071 Shifter ROD TOP Shifter ROD Bottom 435840KIT Harness Conn B&S 181037 Repair Parts Snow Thrower - Model NO. PR827ES DecalsDECAL, Danger DECAL, DANGER, Deflector Service Notes Service Notes Service Notes Limited Warranty