To Remove Wheels See Fig, Carburetor, Engine Speed | Poulan 436134

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 21)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN	OUTER HOLE
	INNER
	HOLE
WHEEL	WHEEL HUB

FIG. 21

TO ADJUST CABLE TENSION (See Fig. 22)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 22

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

18

Image 18

Poulan 436134, 96192004300 owner manual To Remove Wheels See Fig, To Adjust Cable Tension See Fig, Carburetor, Engine Speed

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Traction Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See Fig Using the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Maintenance Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Service Notes Scraper BAR Auger HousingKEY Part Description Auger Bearing Skid Plate LH Auger 27 LHAuger 27 RH Skid Plate RH Exploded Bearing Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Impeller Pulley Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Cable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Pivot Support Weldment Repair Parts Snow Thrower - Model NO. PR827ES HandlesLower Handle Loop Handle LH Headlight Bezel Wire HarnessConsole Panel Flood Headlight Handle Knob SpacerKnob RED Washer 3/8 Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD Bottom Repair Parts Snow Thrower - Model NO. PR827ES Drive Speed Selector AssemblyDrive Plate Assembly Rubber Ring Sprocket Axle ShaftRoll PIN 3/16 Clik PIN 436146X421 Engine Model 12A114Frame Engine Mount Plate Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley 432335X428 Repair Parts Snow Thrower - Model NO. PR827ES WheelsWheel Assembly LH 432336X428 Repair Parts Snow Thrower - Model NO. PR827ES BAG of Parts Safety Ignition KEY193071 Shifter ROD TOP Shifter ROD Bottom 435840KIT Harness Conn B&S DECAL, Danger Repair Parts Snow Thrower - Model NO. PR827ES Decals181037 DECAL, DANGER, Deflector Service Notes Service Notes Service Notes Limited Warranty