193071, Safety Ignition KEY | Poulan 436134, 96192004300 specs

REPAIR PARTS SNOW THROWER - - MODEL NO. PR827ES (96192004300)

BAG OF PARTS

01.14.003-B

		KEY	PART
4		NO.	NO.	DESCRIPTION
4		1	198563	POWER CORD
5	6	1	198563	POWER CORD
5	8	2	169675	RETAINER PIN
7		2	169675	RETAINER PIN
		3	180684X008	WRENCH
		3	180684X008	WRENCH
		4	184505	REMOTE SPRING
		5	179829	SHOULDER BOLT 1/4-20
	9 10	6	191730	LOCKNUT 1/4-20
	9 10	7	72250505	CARRIAGE BOLT 5/16-18 X 5/8
		7	72250505	CARRIAGE BOLT 5/16-18 X 5/8
		8	751153	LOCKNUT 5/16-18
		9	73800600	LOCKNUT 3/8-16
		10	19131316	WASHER 3/8
	12	11	192090	SHEAR BOLT 1/4-20 X 1-13/16
1	12	12	73800400	LOCKNUT 1/4-20
	11

	KEY	PART
	NO.	NO.	DESCRIPTION
1	1	193071	SAFETY IGNITION KEY

01.14.007-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 38

Page 38

Image 38

Poulan 436134, 96192004300 Repair Parts Snow Thrower - Model NO. PR827ES BAG of Parts, 193071, Safety Ignition KEY

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Traction Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Maintenance Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Service Notes Scraper BAR Auger HousingKEY Part Description Auger Bearing Skid Plate LH Auger 27 LHAuger 27 RH Skid Plate RH Exploded Bearing Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Impeller Pulley Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Cable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Pivot Support Weldment Repair Parts Snow Thrower - Model NO. PR827ES HandlesLower Handle Loop Handle LH Headlight Bezel Wire HarnessConsole Panel Flood Headlight Handle Knob SpacerKnob RED Washer 3/8 Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD Bottom Repair Parts Snow Thrower - Model NO. PR827ES Drive Speed Selector AssemblyDrive Plate Assembly Rubber Ring Sprocket Axle ShaftRoll PIN 3/16 Clik PIN 436146X421 Engine Model 12A114Frame Engine Mount Plate Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley 432335X428 Repair Parts Snow Thrower - Model NO. PR827ES WheelsWheel Assembly LH 432336X428 193071 Repair Parts Snow Thrower - Model NO. PR827ES BAG of PartsSafety Ignition KEY KIT Harness Conn B&S Shifter ROD TOP Shifter ROD Bottom435840 DECAL, Danger Repair Parts Snow Thrower - Model NO. PR827ES Decals181037 DECAL, DANGER, Deflector Service Notes Service Notes Service Notes Limited Warranty

REPAIR PARTS SNOW THROWER - - MODEL NO. PR827ES (96192004300)

BAG OF PARTS

KEY

SHOULDER BOLT 1/4-20

WASHER 3/8

KEY

193071

SAFETY IGNITION KEY