Check Tire Pressure

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Eyelet will be loose on shoulder bolt.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

	1/4-20	SPRING
	1/4-20	CHUTE
	SHOULDER	CHUTE
	SHOULDER	DEFLECTOR
	BOLT	DEFLECTOR
	BOLT
		HOOK
		BETWEEN
		HEX NUTS
		ON CHUTE
	1/4-20	ROTATER
	LOCKNUT	HEAD
		5/16-18
		CARRIAGE
		BOLT
	CABLE
	EYELET
	REMOTE
	CABLE
	BRACKET
	5/16-18
	LOCKNUT

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI.

Page 7

Image 7

Poulan 96192004300, 436134 owner manual Install Chute Deflector Remote Control See Figs, Check Tire Pressure

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Traction OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements To Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See Fig To Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Maintenance Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting Service Notes Auger Bearing Auger HousingKEY Part Description Scraper BAR Skid Plate RH Auger 27 LHAuger 27 RH Skid Plate LH Exploded Impeller Pulley Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Bearing Deflector Seal Deflector Control AssemblyChute Weldment Deflector Weldment Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat Shield Loop Handle LH Repair Parts Snow Thrower - Model NO. PR827ES HandlesLower Handle Pivot Support Weldment Flood Headlight Wire HarnessConsole Panel Headlight Bezel Washer 3/8 SpacerKnob RED Handle Knob Shifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOP Repair Parts Snow Thrower - Model NO. PR827ES Drive Rubber Ring AssemblyDrive Plate Assembly Speed Selector Clik PIN Axle ShaftRoll PIN 3/16 Sprocket Engine Mount Plate Engine Model 12A114Frame 436146X421 Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket 432336X428 Repair Parts Snow Thrower - Model NO. PR827ES WheelsWheel Assembly LH 432335X428 Safety Ignition KEY Repair Parts Snow Thrower - Model NO. PR827ES BAG of Parts193071 435840 Shifter ROD TOP Shifter ROD BottomKIT Harness Conn B&S DECAL, DANGER, Deflector Repair Parts Snow Thrower - Model NO. PR827ES Decals181037 DECAL, Danger Service Notes Service Notes Service Notes Limited Warranty

Poulan 96192004300, 436134 Install Chute Deflector Remote Control See Figs, Check Tire Pressure

Models: 96192004300 436134

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

CHECK TIRE PRESSURE