Manuals / Pride Mobility / Personal Care / Mobility Aid

Pride Mobility 1107 owner manual Seat Installation, To install the seat initial installation

Models: 1107

1 51

Download 51 pages 2.1 Kb

Page 21

I V . A S S E M B L Y / D I S A S S E M B L Y

Seat Installation

It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Most seats are attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts that may be attached to any medium-back or high-back seat, regardless of seat width or seat depth. The two main components are aluminum extrusions mounted to the seat base. These extrusions attach to a set of trapeze bars that are mounted to the power base (see figure 12).

WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so, resulting in personal injury or damage to the chair.

NOTE: Prior to initial installation, the rear seat in- terface needs to be installed to the seat base.

To install the seat (initial installation):

1.Slide the rear seat interface into the rear extrusion. See figure 11.

2.Squeeze the retaining pin and clip it onto the rear seat interface.

3.Slide the seat onto the side trapeze bars and slowly lower the seat onto the front trapeze bar until it locks into place. See figure 12.

4.Flip the seat latch safety down. See figure 12.

WARNING! Make sure the seat latch safety is flipped down before using your power chair.

5.Install the controller into one of the armrests. See figure 10.

6.Tighten the setscrew on the armrest. See figure 22.

7.Route the controller cable so that it cannot be pinched in the seat hinge.

8.Secure the controller cable to the armrest receiver with one or more wire ties.

To remove the seat:

1.Flip up the seat latch safety.

2.Squeeze the seat latch together. See figure 12.

3.Pull the front of the seat up.

4.Slide the seat forward and off of the power base.

REAR SEAT INTERFACE	REAR EXTRUSION
RETAINING PIN
	FRONT EXTRUSION

Figure 11. Assembly View (Rear Seat Interface Installation)

SEAT LATCH

SAFETY

SIDE

TRAPEZE

BARS

SEAT LATCH

FRONT TRAPEZE

BAR

Figure 12. Seat Installation

Jazzy 1107

www.pridemobility.com

21

Image 21

Pride Mobility 1107 owner manual Seat Installation, To install the seat initial installation, To remove the seat

Contents

Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S III N T E N T SN T R O D U C T I O N SafetyPURCHASER’S Agreement Information ExchangeMy Authorized Pride Provider Pride Owners ClubS a F E T Y Product Safety SymbolsS a F E T Y Modifications Pre-Ride Safety CheckWeight Limitations Tire InflationIncline Information Braking Information Cornering InformationOutdoor Driving Surfaces Stationary Obstacles Steps, Curbs, etc Freewheel ModePublic Streets and Roadways Stairs and Escalators DoorsElevators TransfersLift/Elevation Products Motor Vehicle TransportPositioning Belts Inclement Weather PrecautionsBatteries Reaching and BendingElectromagnetic and Radio Frequency Interference EMI/RFI AlcoholJazzy I . Y O U R P O W E R C H a I RJazzy 1107 Power Base Electrical Components Jazzy 1107 SpecificationsJazzy 1107 Electrical Components Flight Controller Shown To engage or disengage the drive motors Manual Freewheel LeversA S S E M B L Y / D I S a S S E M B L Y Initial AssemblySeat Installation To install the seat initial installationTo remove the seat To disassemble the power base Power Base DisassemblyBattery Box Removal and Frame Separation Seat Height and Seat Angle Adjustment Comfort AdjustmentsO M F O R T a D J U S T M E N T S To change the seat heightManual Recline Seatback Adjustment Seatback Angle AdjustmentArmrest Width Adjustment Seat PositionFoot Platform Height Adjustment Armrest Angle AdjustmentFoot Platform Depth Adjustment Quick Release FastenersController Position Foot Platform Angle AdjustmentSwing-away Footrests Elevating Leg RestsMulti-Axis Foot Plates To change foot plate position B To adjust the anti-tip wheelsTo change foot plate tilt C To change foot plate angle DB a T T E R I E S a N D C H a R G I N G Batteries and ChargingCharging the Batteries Frequently Asked Questions FAQs Battery Break-inHow often must I charge the batteries? Why do my new batteries seem weak?Daily Use Infrequent UseHow should I store my power chair and its batteries? How can I ensure maximum battery life?What about public transportation? What about shipping?Flight Controller I . O P E R a T I O NFlight consists JoystickLock Mode Battery Condition MeterOn/Off Key Horn KeyError Codes Sleep Mode If EnabledError Code Probable Cause Possible Solution Speed KeysVSI consists VSI Electronic ControllerSpeed/Profile Keys Red lights only lit or slow flash Charge batteries as soonController Connector Actuator Connector OptionalActuator Keys and Actuator Lights For Optional Equipment Locking/Unlocking the VSIThermal Rollback VSI Error CodesShould your power chair come in contact with water Care and MaintenanceTemperature I I . C a R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksTo check the brakes Monthly ChecksCleaning and Disinfection Disposal of Your Power ChairWheel Replacement StorageBattery Replacement I I . C a R E a N DTo replace the batteries Corrective Maintenance When to See Your Authorized Pride Provider for ServiceW a R R a N T Y Warranty Exclusions Reconditioned Units WarrantyService Checks and Warranty Service Exclusions also include components with damage caused byT E S T E S T E S Pride keeps a more detailed report on file at the factory Quality Control