Turning on the Power
To turn on the TV, press the POWER button on the TV or the remote control.
Volume Control
To adjust the volume to the desired level, press the VOLUME + or Ð button.
The sound level will be |
shown by a bar on the TV |
screen. As the sound level |
is increased, the bar will |
CHANNEL PROGRAMMING
Memorizing Channels
The TV is equipped with a channel memorizing function that allows you to step up or down from the current channel to the next channel set into memory. Before channels can be selected in this way, they must be set into the TVÕs memory. Note: When programming chan- nels, if no buttons are pressed for four seconds, the TV will return to the normal screen.
move to the right. As the |
|
|
|
|
|
|
|
|
|
|
|
|
|
| VOLUME |
| |
sound level is decreased, |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
the bar will move to the left. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Note: If no broadcasting |
|
|
|
|
|
|
|
|
signal is received, the sound will be muted and the vol- ume control will be disabled.
Direct Channel Selection (by Remote Control)
Use the channel selection buttons on the remote con- trol to select a channel number. The channel num- ber will appear on the upper right corner of the TV screen. For channels 2 through 9, press the 0 but-
Automatic Memory Tuning
1.Press the MENU button to turn on the pop up menu in the TV mode or CATV mode. Press the MENU button again to select CH MEMORY (channel mem- ory).
2.Press the MENU button again to select AUTO MEMORY.
CH MEMORY ANALOG CLOCK/TIMER
AUTO MEMORY
SEARCH/SKIP MEMORY ADD ¥ERASE
TV/CATV
ton and then press the de- sired channel number (if the
0 button is not pressed first, channel selection will be
delayed for 3 seconds). For channels 10 through 99, press the two digits in order. Be sure to press the sec- ond digit within 3 seconds after pressing the first. For CATV channels over 100, press the
Skip Mode
3. Press the + button to start |
|
|
|
|
|
|
|
| |
AUTO MEMORY. The TV |
| TV | 07 |
|
will begin setting into |
|
| ||
|
|
|
| |
memory all the channels |
|
|
|
|
available in your area. |
| AUTO MEMORY |
| |
When no broadcast signal |
|
| ||
| START [+] |
|
| |
is detected on a channel, |
|
|
| |
|
|
|
| |
|
|
|
| |
the channel is erased from |
|
|
|
|
memory. When a signal is detected, the channel is stored in memory and the next channel is selected.
Press the CHANNEL Æ or Æ button to select memo- rized channels, skipping over empty channels. Hold down the CHANNEL Æ or Æ button to change channels continuously. Note: If no channels are memorized, the TV will switch to the SEARCH mode.
Search Mode
Press the CHANNEL Æ or Æ button to search for the next available channel. Hold down the CHANNEL Æ or
Æbutton to search through all available channels.
Note: Before selecting channels with the CHANNEL Æ or Æ button, the channels must be set into the TVÕs memory. See MEMORIZING CHANNELS at the right.
This process will be re- peated until the highest channel is reached. It then stops at the lowest channel stored in memory, and re- turns to a normal screen after four seconds. The TV will then be in the SKIP mode.
TV 07
AUTO MEMORY END
18
