ProForm PFTL57908.0 Make sure that the power cord is unplugged, Do not fully fold the Frame yet

Models: PFTL57908.0

1 32
Download 32 pages 48.7 Kb
Page 7
Image 7

1. Make sure that the power cord is unplugged.

1

 

 

 

Hole

 

With the help of a second person, carefully tip

 

 

91

 

97

 

the treadmill onto its left side. Partially fold the

 

 

 

 

Frame (48) so that the treadmill is more stable;

 

 

 

 

 

 

6

do not fully fold the Frame yet.

 

 

 

 

96

 

Cut the shipping tie securing the Wire Harness

 

 

 

 

 

 

(91) to the Base (96). Locate the plastic tie in

 

 

 

 

 

 

 

the indicated hole in the Base, and use the tie to

 

 

 

 

 

 

 

pull the Wire Harness out of the hole.

48

98 97 6

 

 

 

 

Attach two Base Feet (97) to the Base (96) in the

 

 

 

 

locations shown with two Base Foot Spacers

 

 

 

 

 

 

 

(98) and two #8 x 1" Tek Screws (6).

 

 

 

 

 

97

Then, attach the other two Base Feet (97) with

 

 

 

 

 

 

 

 

 

 

 

6

two #8 x 1" Tek Screws (6).

 

 

 

 

 

 

 

 

98

97

 

 

 

 

 

 

 

 

 

 

 

2. See the inset drawing. Cut the plastic tie near

2

Plastic Tie

 

 

 

 

the Wire Harness (91).

 

 

 

 

Attach a Wheel (99) with a 3/8" x 2" Bolt (9) and

 

 

 

 

 

 

 

a 3/8" Nut (10) to the Base (96). Do not over-

 

 

 

 

 

 

 

tighten the Nut; the Wheel must turn freely.

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1099

96

 

Cut

 

 

 

 

 

 

91

 

 

3. Identify the Right Upright (92) and the Right

3

 

 

 

 

 

 

Upright Spacer (100), which are marked with

 

 

 

 

 

 

stickers. Insert the Wire Harness (91) through

 

 

 

 

92

 

 

the Right Upright Spacer as shown. Set the

 

 

 

 

 

 

Right Upright Spacer on the Base (96).

91

 

 

 

 

 

 

With the help of a second person, hold the Right

 

 

 

 

91

Wire Tie

 

 

 

Upright (92) near the Base (96). See the inset

 

100

 

drawing. Tie the wire tie in the Right Upright se-

 

 

 

 

 

 

curely around the end of the Wire Harness (91).

 

 

 

 

 

 

96

Then, pull the other end of the wire tie until the

 

 

 

 

 

 

Wire Harness is routed completely through the

 

 

 

 

 

 

 

Right Upright.

 

92

 

 

 

 

 

 

 

 

 

 

 

 

 

91

Wire

 

 

 

 

 

 

Tie

 

 

 

 

 

 

7

 

 

 

 

 

 

Page 7
Image 7
ProForm PFTL57908.0 manual Make sure that the power cord is unplugged, Do not fully fold the Frame yet