2. Attach a Wheel (66) to the base of the Uprights | 2 |
|
|
| 64 |
(69) with a Wheel Bolt (64) and a Nut (13) as |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
shown. Do not overtighten the Wheel Bolt; the |
|
|
| 69 | 66 |
Wheel should turn freely. |
|
|
| ||
|
|
|
| ||
|
|
|
|
| 13 |
3. With the help of a second person, carefully tip | 3 |
|
|
|
|
the treadmill onto its right side as shown. |
|
|
|
| |
|
|
|
|
| |
Partially fold the Frame (86) so the treadmill is |
|
|
|
|
|
more stable. Do not fully fold the treadmill |
|
|
|
|
|
until it is completely assembled. |
|
|
|
|
|
Insert an Extension Leg (63) into the base of the | 66 | 64 |
|
|
|
|
|
| 86 | ||
Uprights (69). Hold an Extension Leg Nut (46) in |
|
| 69 |
| |
|
|
|
| ||
the bottom of the Extension Leg, and thread a |
|
|
|
| |
|
|
|
|
| |
Extension Leg Bolt (93) with a Star Washer (95) | 13 |
|
|
|
|
into the top of the Extension Leg. Next, thread a |
|
|
|
| |
3” Bolt (96) with a Star Washer into the bottom of |
|
|
|
| 93 |
the Extension leg. Firmly tighten the Bolts. | 39 | 57 |
|
| |
|
| 95 | |||
| 57 | 39 |
|
| |
Attach two Base Pads (57) to the base of the |
|
|
| ||
|
|
|
|
| |
Uprights (69) with two 1” Tek Screws (39). |
|
| 95 | 46 |
|
|
| 96 |
| ||
|
|
|
|
| |
Attach the other Wheel (66) to the base of the |
|
|
| 63 |
|
Uprights (69) with a Wheel Bolt (64) and a Nut |
|
|
|
| |
|
|
|
|
| |
(13). Do not overtighten the Wheel Bolt; the |
|
|
|
|
|
Wheel should turn freely. |
|
|
|
|
|
4. If there is a board (not shown) between the | 4 |
|
|
|
|
Uprights (69), remove the two bolts attaching the |
|
|
|
| |
|
|
|
|
| |
board. Discard the board and the bolts. | 93 |
|
|
|
|
|
|
|
|
| |
Remove the tie from the Wire Harness (42). Hold |
| 71 |
|
|
|
one of the Handrails (71) near the right Upright |
|
|
|
| |
95 |
|
| 42 |
| |
(69), and insert the Wire Harness into the open- |
|
|
| ||
| 69 |
|
|
| |
ing in the bottom of the Handrail and out of the |
| 93 |
|
| |
indicated hole in the top. |
|
|
|
| |
|
|
|
|
| |
Set the Handrail (71) on the right Upright (69), |
|
| 95 |
| |
and tighten two Handrail Bolts (93) with two |
| 71 |
|
| |
Handrail Star Washers (95) into the Handrail and |
|
|
|
|
|
the right Upright. Make sure that the Wire |
|
|
|
|
|
Harness (42) is not pinched. |
|
|
| 69 |
|
Attach the other Handrail (71) to the left Upright |
|
|
|
|
|
(69) as described above. Note: There is not a |
|
|
|
|
|
wire harness on the left side. |
|
|
|
|
|
| 7 |
|
|
|
|
