Manuals
/
QSC Audio
/
Home Audio
/
Stereo System
QSC Audio
DSP-3 manual
Models:
DSP-3
1
35
36
36
Download
36 pages
47.43 Kb
29
30
31
32
33
34
35
36
<
>
Specifications
Install
Introduction- Block Diagram
Warranty
Speakers Connected For Your Intended Configuration
Connecting Audio Inputs And Outputs
Appendix- Preset Operation Notes
Multiple Delays
DSP-3 Digital Signal Processor
Explanation Of Graphical Symbols
Page 35
Image 35
Page 34
Page 36
Page 35
Image 35
Page 34
Page 36
Contents
Rev.D
Amplifier Accessory Hardware Manual
DSP-3 Digital Signal Processor
TD-000087-00* TD-000087-00
Page
Hardware Features and Functions
TABLE OF CONTENTS
Section 2 INSTALLATION
Connector & Indicator Descriptions, Illustrations
Federal Communications Commission FCC Information
IMPORTANT SAFETY INFORMATION PLEASE REVIEW
EXPLANATION OF GRAPHICAL SYMBOLS
SAFEGUARDS
Section 1 Introduction- Overview
Section 1 Introduction- DSP-3 General Use Guidelines
Then you need to
Section 1 Introduction- Quick Start
TURN THE EQUIPMENT OFF & INSTALL THE HARDWARE
If you are using the DSP-3 with
CONNECT THE AUDIO INPUTS
TURN THE AMP GAIN DOWN, POWER UP THE AMPLIFIER & THE DSP-3
the CHANNEL 1 INPUT & CHANNEL 2 INPUT connectors
Section 1 Introduction- Quick Start
Section 1 Introduction- Quick Start
WHAT THE SIGNAL MANAGER APPLICATION LOOKS LIKE
INSTALL THE SOFTWARE
Section 1 Introduction- Quick Start
SPEAKERS CONNECTED FOR YOUR INTENDED CONFIGURATION
CREATE A SIMPLE DSP CONFIGURATION
Signal Manager and restart it so that the newly selected
Section 1 Introduction- Quick Start
FRONT PANEL
Section 1 Introduction- Basic Connector & Indicator Descriptions
DATAPORT unlabeled- This is the “output”
REAR PANEL
OVERALL
Section 1 Introduction- Basic Connector & Indicator Descriptions
High- and Low-Pass Shelf Filter
Section 1 Introduction- List of Functions & Features
Multiple Delays
High- and Low-Pass Crossover
Signal Attenuation mute or bypass
Section 1 Introduction- List of Functions & Features
Signal Compressor
Signal Level Meter
Section 1 Introduction- Block Diagram
Audio Output Path
Section 1 Introduction- Technical Overview
Power Supply
Audio Input Path
UNPACKING
Section 2 Installation- Unpacking and Mounting
WHAT IS INCLUDED IN THE CARTON
Page
Balanced connection is recommended for all inputs
Section 2 Installation- Connections
CONNECTING AUDIO INPUTS AND OUTPUTS
The recommended stripping length for the wires is approximately 6 to
male similar to VGA computer monitor cables. Do not use com
Section 2 Installation- Connections
The front-panel DataPort connection is used for connecting to
QSC DataPort products. Use a QSC DataPort cable male-to
DAISY-CHAINING THE DSP-3 OUTPUTS TO ADDITIONAL AMPLIFIERS
Section 2 Installation- Connections
POWER SOURCE
CONNECTION TO ACCESSORY EXTERNAL DC
Section 2 Installation- Application Examples
DSP-3 Remotely Mounted used with QSC DataPort Amplifier. Audio Input via Terminal Block Inputs
Section 2 Installation- Application Examples
Section 2 Installation- Application Examples
OVERALL NOTES AND WARNINGS
Section 3 Signal Manager Software- Software Installation
Software Installation
Note Specifications are subject to change without notice
Section 3 Specifications
Signal Processing 24 bit, 48 kHz
Power amplifier connectivity
General
Section 3 Specifications
Note Specifications are subject to change without notice Dimensions
Accessory External Power Supply
The Digital Signal Processor shall be the QSC DSP-3
Section 4 Architect’s and Engineer’s Specifications
Hard Ground
Section 5 Appendix- DataPort Pinout
AC Standby Control
Clip/Protect Ch
3 pin WITH Strain Relief Phoenix Contact 17
Section 5 Appendix- RS-232 Port Pinout & Connector P-N’s
APPLICATION INFORMATION
Section 5 Appendix- Application Information
The reason
Section 5 Appendix- Preset Operation Notes
SPECIAL INFORMATION CONCERNING SAVED DSP-3 CONFIGURATIONS
Warranty Information
Section 6 Maintenance, Warranty & QSC Contact Information
Cleaning
User Maintenance
Page
Copyright 2001, QSC Audio Products, Inc
