Quadra-Fire QUADRA-FIRE CONTOUR warranty Safety Label, Contour Pellet Stove

Contour Pellet Stove

SAFETY LABEL

LABEL LOCATION: BEHIND LEFT SIDE CURTAIN ON OUTSIDE OF HOPPER

OMNI-Test Labs, Inc.			Model:	Serial No.
Beaverton, OR			QUADRA-FIRE CONTOUR
Report No. 061-S-20-2			Room Heater Pellet Fuel BurningType
Listed by	O-T L	Oregon USA			1445 North Highway
			Also for use in Mobile Homes. This pellet burning appliance has been tested and listed
Tested and		Beaverton
	C		for use in Manufactured Homes in accordance with		Colville, WA 99114
OMNI-Test Laboratories, Inc.			OAR 814-23-900 through 814-23-909

'PREVENT HOUSE FIRES"

Install and use only in accordance with manufacturer's installation and operating instructions. Contact Local Building or Fire Officials About Restrictions and Inspection in Your Area.

WARNING - FOR MANUFACTURED HOMES: Do not install appliance in a sleeping room. An outside combustion air inlet must be provided. The structural integrity of the manufactured home floor, ceiling and walls must be maintained.

Refer to manufacturer's instructions and local codes for precautions required for passing chimney through a combustible wall or ceiling. Inspect and clean exhaust venting system frequently in accordance with manufacturer's instructions.

Use a 3" or 4" diameter type "L" or "PL" venting system.

Do not connect this unit to a chimney flue servicing another appliance.

Tested to:

ASTM E 1509, and ULC-C1482-M1990 Room Heater Pellet Fuel Burning type (UM) 84-HUD

Input Rating Max 4 lb. fuel/hr.

Electrical Rating: 115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 AMPS. Route power cord away from unit

DANGER: Risk of electrical shock. Disconnect power supply before servicing.

Replace glass only with 5mm ceramic available from your dealer

To start, set thermostat above room temperature, the stove will light automatically. To shutdown, set thermostat to below room temperature. For further instruction refer to owner's manual.

Keep viewing and ash removal doors tightly closed during operation.

FOR USE WITH PELLETIZED WOOD FUELOR SHELLED FIELD CORN ONLY.

Minimum Clearances to Combustible Materials

AC

BC

DF

	E	F
A	Back Wall to Appliance		2"/5cm
B	Side Wall to Appliance		6"/15cm
Corner Installation:
C	Walls to Appliance		2"/5cm
Vertical 3" - 6" Adapter Kit (Part #812-3570) Installation:
D	Back Wall to Appliance Flue			3"/8cm
E	Side Wall to Appliance		6"/15cm
Corner Installation with Vertical Adapter Kit:
F	Walls to Appliance		2"/5cm
Alcove Installation:
Min. Alcove Height:			43"/1092cm
Min. Alcove Side Wall			6"/15cm
Max. Alcove Depth			36"/91cm

FLOOR PROTECTION

*H

GG

I

G = 2"/5cm

H = 2"/5cm *See Exceptions Below

I = 6"/15cm

Use a non-combustible floor protector extending under unit and to the sides, front and back of unit as shown in Floor Protection Diagram. Measure front distance

(I)from the surface of the glass door.

*Exceptions: Non-combustible floor protection must extend beneath the fluepipe when installed with horizontal venting or under the top vent adapter with vertical installation.

Note 1: In residential installations, when using parts #811-0860, (3" - 3" Top Vent Adapter) and #812-3570 (3" - 6" Offset Adapter), 24 gauge 6" single wall flue connector may be used.

Note 2: In manufactured home installation, when using part #811-0860, (3" - 3" Top Vent Adapter) and #812-3570 (3' - 6" Offset Adapter), use listed double wall flue connector. An Outside Air Kit (#811-0871), must be used with manufactured home installation.

U.S. ENVIRONMENTAL PROTECTION AGENCY

This model is exempt from EPA certification under 40 CFR 60.531 by definition [Wood Heater (A) "Air-to-Fuel Ratio"].

Date of Manufacture

2000 2001 2002 JAN FEB MAR APR MAY JUNE JULY AUG SEPT OCT NOV DEC

DO NOT REMOVE THIS LABEL MADE IN U.S.A.

October 10, 2001 4 250-5583