11.Press 7. Iý'&<J appears. To change the distance between the
listening position and the rear (surround) speakers, repeatedly press 8or 9 until you reach the desired level (&ýto )&ý<J).
12.Press ENTER. <HEDJ appears.
13.Press SETUP to exit.
Surround Effects
Important: The center and rear speakers only operate when the unit is set to a surround sound mode and the source material being played is recorded or broadcast in Dolby Digital, DTS or Dolby Pro Logic surround sound.
Stereo broadcasts or recordings will produce some rear channel ef- fects when played in a surround mode. However, mono sources will not produce any sound from the rear speakers.
Changing System Settings - Special Circumstances
When you make a copy of DVD/CD via TAPE output, set the front speaker size to <#B7H=;. Set the surround mode to IJ;H;E.
USING THE REMOTE CONTROL UNIT TO CONTROL ADDITIONAL COMPONENTS
You can set your remote control to control other components such as a VCR, TV, satellite receiver or cable box.
1.Turn on the component to be programmed.
2.Look up the brand and corresponding code(s) in the code list (see “Manuracturer’s Codes” on Page 23).
3.While holding down the appropriate source button (VCR, TV, or SAT) on the remote control, use the number keys enter the first code from the code list.
4.Release the component button, then press POWER.
If you have entered the correct code, the component turns off.
If the component does not turn off, repeat Steps 3 and 4 and subustitute use the next code (if available) listed for the brand of your component until the component responds to the remote command.
Note: To turn on or off the receiver when you select the VCR, SAT, or TV function, press POWER twice.
Cautions:
•This remote control unit may not operate on all models of the brands shown.
•If batteries are removed from the battery compartment of the remote unit, replace the batteries within 30 minutes or the codes are lost. You must then
•The buttons on the remote control unit may not work correspond- ingly with those on the components brands.
•Experiment with the remote control and your components to see which buttons work. If only a few functions operate, repeat Step 4 to see if another code operates more buttons.
CONTROLLING THE TUNER
1.Press POWER. The last selected function appears.
2.Press TUNER.
3.Press BAND to select the desired band.
4.Repeatedly press TUNING/PRESET ) or - to tune in the desired station.
To change the frequency by one step, press TUNING/PRESET ) or - quickly (less than half a second).
To tune to the next clear frequency, hold down TUNING/PRE- SET )or
Listening To FM Stereo Broadcasts
In FM mode, press to select stereo or mono. When you se- lect the stereo mode, IJ appears to the right of Jkd[Z. It goes off when you select mono.
When you listen to very weak FM stereo stations, you might hear
Presetting Radio Stations
You can preset 30 AM and 30 FM stations regardless of the recep- tion. Tune in the desired stations using auto or manual tuning.
Manual Preset
1.Press BAND to select the desired band.
2.Repeatedly press TUNING/PRESET ) or - to tune in the desired station.
To change the frequency by one step, press TUNING/PRESET ) or - quickly (less than half a second).
To tune to the next clear frequency, hold down TUNING/PRESET
) or
3.Press MEMORY. C;CE flashes for 5 seconds. When C;CE goes off, press the button again (C;CE flashes again).
4.Select the preset number with TUNING/PRESET ) or
5.Press MEMORY again.
6.Repeat Steps
To store stations on the other band, repeat Steps
Note: If you want to store more stations later, you might find that pressing TUNING/PRESET ) or - only moves the tuner to the next preset station (instead of moving the frequency one step). If this hap-
pens, pressto return to manual tuning (see “Switching Between Preset Stations and Manual Tuning”).
14 | Remote Control Operation |
