Manuals / Raypak / Lawn and Garden / Swimming Pool Heater

Raypak 185A NEW CIRCUIT BOARD & GASKET INSTALLATION USING OLD BEZEL - MODELS 185, Remove Backing

Models: 185A

1 18

Download 18 pages 43.7 Kb

Page 9

Image 9

NEW CIRCUIT BOARD & GASKET INSTALLATION USING OLD BEZEL - MODELS 185, 265,

Page 9

P/N 241169 Rev.-3

NEW CIRCUIT BOARD & GASKET INSTALLATION USING OLD BEZEL - MODELS 185, 265,

335 & 405, A & B SERIES:

Make sure the power and gas are off.

Note: Disregard window gasket installation if already present.

1.Remove backing on gasket and install adhesive side on the control panel bezel as shown in Fig. 21.

2.Re-assemble with new board to plastic bezel using the three mounting screws as shown in Fig. 22 & Fig. 23.

		GASKET
		STICKY SIDE TO
REMOVE BACKING		STICKY SIDE TO
REMOVE BACKING		PLASTIC BEZEL

CLEAR

WINDOW

Fig. 21

LAY BOARD

DOWN

RE-ASSEMBLE WITH NEW BOARD	Fig. 22
MOUNTING SCREWS

NOTE: DO NOT

RE-INSTALL

SCREW HERE

Fig. 23

2151 Eastman Ave., Oxnard, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.com Technical support is available M-F, 5:30 AM to 5:00 PM PST, at 800-947-2975 or 800-627-2975

Page 9

Image 9

Raypak 185A NEW CIRCUIT BOARD & GASKET INSTALLATION USING OLD BEZEL - MODELS 185, 335 & 405, A & B SERIES, Remove Backing

Contents

P.C. BOARD, TEMPERATURE CONTROL & SENSOR KIT #010253F FOR ALL RAYPAK REPLACEMENT INSTRUCTIONSThis kit includes IMPORTANT NOTICEACCESSING THE BOARD - MODELS ACCESSING THE BOARD - MODELS 185A/B, 265A/B, 335A/B, 405A/B206A, 207A, 266A, 267A, 336A, 337A, 406A, 407A Fig. 4 Close-upUNPLUG ALL CONNECTORS REMOVING THE CIRCUIT BOARD - MODELS 185A/B, 265A/B, 335A/B, 405A/BP/N 241169 Rev.-3 REMOVE KEYBOARD RIBBON1. Unplug all connectors from old circuit board. Fig Make sure the power and gas are offUNPLUG ALL CONNECTORS REMOVE KEYBOARD RIBBON 2. Unplug keypad ribbon from old circuit board1. Unplug all wires and connectors from ignition control. See Fig Make sure the power and gas are offUNPLUG ALL WIRES can be left in place but not usedMake sure the power and gas are off PROPANE HEATERS ONLY1. Locate the propane tab on the board as shown in Fig 2. Break off tab with pliers as shown in Fig. 13 & FigMake sure the power and gas are off MODELS 185, 265, 335 & 405, A & B SERIES, LOW NOX ONLY2. No additional wiring or connections are necessary 1. DO NOT break tab See Fig. 15 and Fig.16BREAK TAB WIRE AIR SWITCH TO P-10 HERE LOW NOX MODELS 207A, 267A, 337A & 407AP/N 241169 Rev.-3 LO NOX335 & 405, A & B SERIES NEW CIRCUIT BOARD & GASKET INSTALLATION USING OLD BEZEL - MODELS 185REMOVE BACKING LAY BOARD DOWNLAY BEZEL DOWN REMOVE BACKINGPage SHIELD BRACKETS INSTALLING PILOT HI TENSION 206 TO 267A Ensure the power and the gas has been shut offINSTALLING PILOT HI TENSION WIRE EXTENSION SIZES 335A TO 407A Ensure the power and the gas has been shut offPage P/N 241169 Rev.-3Page P/N 241169 Rev.-3Page P/N 241169 Rev.-3Page P/N 241169 Rev.-3Page P/N 241169 Rev.-3