Manuals / Raypak / Lawn and Garden / Swimming Pool Heater

Raypak 185A manual Remove Backing, Lay Bezel Down

Models: 185A

1 18

Download 18 pages 43.7 Kb

Page 10

Image 10

Page 10

P/N 241169 Rev.-3

GASKET & NEW CIRCUIT BOARD NEW BEZEL INSTALLATION - MODELS 206A, 207A, 266A, 267A, 336A, 337A, 406A, 407A:

Make sure the power and gas are off.

Note: Disregard window gasket installation if already present.

1.Remove backing on gasket and install adhesive side on the control panel bezel as shown in Fig. 24 & Fig. 25.

2.Re-assemble with new board to plastic bezel using the three mounting screws as shown in Fig. 26.

GASKET

ADHESIVE SIDE TO

PLASTIC BEZEL

REMOVE BACKING

LAY BEZEL

DOWN

CLEAR

WINDOW

Fig. 24

Fig. 25

RE-ASSEMBLE WITH NEW BOARD

MOUNTING SCREWS

NOTE: DO NOT

RE-INSTALL

SCREW HERE

Fig. 26

2151 Eastman Ave., Oxnard, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.com Technical support is available M-F, 5:30 AM to 5:00 PM PST, at 800-947-2975 or 800-627-2975

Page 10

Image 10

Raypak 185A manual Remove Backing, Lay Bezel Down

Contents

This kit includes RAYPAK REPLACEMENT INSTRUCTIONSP.C. BOARD, TEMPERATURE CONTROL & SENSOR KIT #010253F FOR ALL IMPORTANT NOTICE206A, 207A, 266A, 267A, 336A, 337A, 406A, 407A ACCESSING THE BOARD - MODELS 185A/B, 265A/B, 335A/B, 405A/BACCESSING THE BOARD - MODELS Fig. 4 Close-upP/N 241169 Rev.-3 REMOVING THE CIRCUIT BOARD - MODELS 185A/B, 265A/B, 335A/B, 405A/BUNPLUG ALL CONNECTORS REMOVE KEYBOARD RIBBONUNPLUG ALL CONNECTORS REMOVE KEYBOARD RIBBON Make sure the power and gas are off1. Unplug all connectors from old circuit board. Fig 2. Unplug keypad ribbon from old circuit boardUNPLUG ALL WIRES Make sure the power and gas are off1. Unplug all wires and connectors from ignition control. See Fig can be left in place but not used1. Locate the propane tab on the board as shown in Fig PROPANE HEATERS ONLYMake sure the power and gas are off 2. Break off tab with pliers as shown in Fig. 13 & Fig2. No additional wiring or connections are necessary MODELS 185, 265, 335 & 405, A & B SERIES, LOW NOX ONLYMake sure the power and gas are off 1. DO NOT break tab See Fig. 15 and Fig.16P/N 241169 Rev.-3 LOW NOX MODELS 207A, 267A, 337A & 407ABREAK TAB WIRE AIR SWITCH TO P-10 HERE LO NOXREMOVE BACKING NEW CIRCUIT BOARD & GASKET INSTALLATION USING OLD BEZEL - MODELS 185335 & 405, A & B SERIES LAY BOARD DOWNREMOVE BACKING LAY BEZEL DOWNPage SHIELD BRACKETS INSTALLING PILOT HI TENSION WIRE EXTENSION SIZES 335A TO 407A Ensure the power and the gas has been shut offINSTALLING PILOT HI TENSION 206 TO 267A Ensure the power and the gas has been shut offP/N 241169 Rev.-3 PageP/N 241169 Rev.-3 PageP/N 241169 Rev.-3 PageP/N 241169 Rev.-3 PageP/N 241169 Rev.-3 Page