Resetting your SpeedTouch, Hardware reset Software reset | RCA 546

Chapter 6

Troubleshooting

6.3 Reset to Factory Defaults

Resetting your SpeedTouch™

You might consider a reset to factory defaults as described below.

!	Be aware that a reset to factory defaults will revoke all configurational
	changes you made to the SpeedTouch™.

You can choose between:

Hardware reset

Software reset

A reset to factory default settings deletes the configuration profile settings.

Therefore, after the reset, a reconfiguration of your SpeedTouch™ will be needed.

Hardware reset Proceed as follows:

1Make sure the SpeedTouch™ is powered on.

2Use a pen or an unfolded paperclip to push the recessed reset button on the back panel. The reset button is marked with a red circle. Keep it pushed until the power LED lights red - this will take about 7 seconds.

15VAC ON/OFF

1

2

3

4

3Release the reset button.

4The SpeedTouch™ restarts.

Software reset Proceed as follows:

1Go to the SpeedTouch™ web pages.

2In the menu select SpeedTouch > Configuration.

3In the Pick a task... list, click Reset my SpeedTouch to default settings.

4The SpeedTouch™ restarts.

5The SpeedTouch™ returns to the SpeedTouch™ Home page (unless the IP address of your computer is not in the same subnet as the default IP address of the SpeedTouch™, being 192.168.1.254).

E-DOC-CTC-20050429-0100 v1.0	91

Image 99

RCA 546 manual Resetting your SpeedTouch, Hardware reset Software reset

Contents

SpeedTouch546 Page SpeedTouch 546 Copyright TrademarksDocument Information Contents Navigation Ethernet Troubleshooting Upgrade Troubleshooting Troubleshooting Contents About this User’s Guide About this User’s Guide Your SpeedTouch Hardware Specifications Software Features SpeedTouch Features Isdn Hardware Specifications Software Features Chapter SpeedTouch LED Behaviour Indicator Description Name Colour State Access Method Can be used to How to Access your SpeedTouch Access via the Web Interface Access via CLI Command Line Interface CLIFor more information, see Quote site command on Username Administrator Select All Programs Accessories Command Prompt Access via FTP Open a Command Prompt windowFile Transfer Protocol FTP Command You can use to Common FTP commands Home/doejohn1$ftp 192.168.1.254 Connected to Remote Assistance Disabling remote access Local Network Setup Menu select Home Network Devices Device settings Ethernet link check Internet Connectivity Dial-In Clients See 3.1 SpeedTouch Web Pages on page 21 to proceed SpeedTouch Web Pages Terminating an Internet session Control on IGD Control AgentStarting an Internet Session Internet connection status Terminating an Internet session MS Windows XP BroadBand Connection Prerequisites Configuring a broadband connection Chapter Network and Dial-up connections YourISP Starting a broadband Internet session Click Disconnect Terminating a broadband Internet session Mac OS X PPPoE Dial-in Client On the Apple menu, click System PreferencesClick Apply Now Chapter Documentation SpeedTouch Web InterfaceIntroduction SpeedTouch Menu Language Bar Navigation Bar Notification Area Tasks Navigation Toolbox MenuCollapsing and expanding the menu SpeedTouch Language Bar Navigation Bar Notification Area Tasks Home SpeedTouch homeSpeedTouch Broadband Connection Toolbox Home Network SpeedTouch Information Configuration Event Logs Update Information Pick a task... list, click Set up SpeedTouch Easy Setup Pick a task... list, click Restart Accessing the RestartRestart Restarting your SpeedTouch Configuration Restoring a previously saved configuration Backup & RestoreAccessing the Backup & Restore Saving your current configuration Reset to Factory Defaults Event Logs Indicator Description Updating the SpeedTouch system software Update Internet Services Broadband ConnectionBroadband Connection menu Click Check Connectivity Connectivity Check DSL Connection Internet Services On the Broadband Connection menu click Internet Services Internet Service SettingsAccessing the Internet Service Settings Toolbox URL Username Password Game & Application Sharing Defined Games & Applications Accessing the Defined Games & Applications Adding a Port Translation rule Accessing the Game or Application Definition OverviewConfigure Under Game or Application Definition New Game or Application Parental Control Block is selected under Action for Unknown Sites Allow is selected under Action for Unknown Sites Under Content Based Filtering you are able to Click Redirect in the Action listClick Allow in the Action list Click Standard Accessing this page Proceed as followsWeb Filtering Activation Web Filtering Activation Standard license activation Icon Description Content Level Under Pick a task..., click Create a new content level New Content LevelContent level creation Proceed as follows Content level configuration Content level definition Chapter High Firewall Intrusion Detection Dynamic DNS On the Dynamic DNS page, click Configure User Management Accessing the User Edit Editing a user account Edit UserOn the Toolbox menu, click User Management Change Default User Changing the defaultUser Add User Home Network DevicesInterfaces Devices Device Settings Accessing the device settings OverviewConnection Sharing Server, as described in 4.5.2 Game & Application Sharing on Assign Public IP Interfaces Interface Settings Assigning a new IP address to the SpeedTouchUnder IP Addresses Accessing the Dhcp Pool Dhcp PoolOn the Home Network menu, click Interfaces Dhcp Pool System software upgrades Software Upgrade Upgrade Wizard on Setup CD Introduction Starting the Upgrade WizardSee Upgrade procedure on page 83 to continue Upgrade procedure System software downgrade Troubleshooting SpeedTouch does not work SpeedTouch unreachable General SpeedTouch Troubleshooting LAN LED does not light up Ethernet Troubleshooting Upgrade Troubleshooting UPnP on Windows XP Systems Adding IGD Discovery Control Hardware reset Software reset Resetting your SpeedTouch Chapter Page Need more help?