AUTO CLOCK SETTING
Your player automatically sets the clock once the EDS channel is set.
Before you begin:
•make sure the antenna cable is connected and then connect the power cord.
•turn on your TV and select the video channel.
•turn on your VCR.
Important: When using a cable box, leave the cable box turned on and select a channel that carries EDS signals.
1. | Press MENU. |
| |
2. | Press | or | to select CLOCK, and press ENTER. |
3. | Press | or | to select AUTO, and press ENTER. |
4. | Press | or | to set EDS CH SET to MANUAL, and press . |
5. | Press | or | to select a channel that carries EDS signals. The |
number of channels that can be selected depends on the CHANNEL PRESET setting.
When using a cable box, select the output channel (03 or 04) on the cable box.
6.Press ENTER to confirm your selection and exit. The screen returns to normal.
Notes:
•When you press MENU for the first time, or after the power is interrupted for more than 5 seconds, the LANGUAGE screen appears.
•If you select a channel in Step 4 that does not carry an EDS signal, the Auto Clock Setting function does not operate.
•If you entered incorrect data during the setup procedure, repeat Steps 1 – 6 above and enter the correct data.
•The number of channels that can be selected depends on the
CHANNEL PRESET setting (AIR or CATV).
AIR/CATV | Available Channels |
|
|
|
|
AIR | 02 to 69 |
|
|
CATV | 01 to 125 |
|
|
• If you press MENU to exit, the data will not be stored.
7. | Repeatedly press | or | , or press the corresponding number | ||
| buttons, to set the time and date. | ||||
8. | Press the AM/PM (+10) to select AM or PM. | ||||
9. | Press | to select DATE. |
| ||
10. | Repeatedly press | or | to select the desired date. | ||
11. | Press | to select YEAR. |
| ||
12. | Press | or | to select the desired year. | ||
13. | Press | to select DST. (See “Automatic Daylight Savings Time | |||
| (D.S.T.) Adjustment” .) |
| |||
14. | Press | or | to turn DST ON or OFF. | ||
15. Press ENTER to accept the changes and exit.
Notes:
•When you press MENU for the very first time, or after the power is interrupted for more than 5 seconds, the LANGUAGE screen appears.
•If you entered incorrect data during the setting procedure, repeat the steps above and enter the correct data.
•If you press MENU to exit in Step 15, the data will not be stored.
AUTOMATIC DAYLIGHT SAVINGS TIME (D.S.T.) ADJUSTMENT
This VCR is equipped with an internal Automatic Daylight Savings Time Adjustment function. In Spring and Fall, the time is adjusted automatically. This function was preset to ON at the factory. Set the D.S.T. mode in the clock setting screen.
Note: If the timer recording program is affected by the D.S.T. time change, check your TV listing and find out when it reflects the time change. Some TV listings will indicate the time change in the same manner as is programmed in this VCR. But others do not show the time change until the next morning. In that case, when programming a timer, use the CLOCK screen to set the D.S.T. mode to OFF so the time change is not carried out.
Spring — Recording timer programs set between 2:00 AM and 3:00 AM are not carried out.
Fall — Because there will be two time frames from 1:00 AM to 2:00 AM, recording timer programs set between these times are not carried out.
MANUAL CLOCK SETTING
1.Turn on your TV and select the video channel. (See “Setting the Output Channel” on Page 16.)
2.Press VCR ON/OFF to turn on the VCR (the VCR POWER LED lights) and press TV/VCR to select VCR (the VCR LED lights).
3.Press MENU.
4. | Press | to select CLOCK, and press ENTER. | |
5. | Press | or | to select MANUAL, and press ENTER. |
6. | Press | or | to select TIME. |
18
LANGUAGE
When you use the VCR for the first time, or after the power is interrupted for more than 5 seconds (power failure, etc.), you must reset the MENU screen language.
1.Turn on your TV and select the video channel. (See “Setting the Output Channel” on Page 16).
2.Press POWER 1to turn on the player. Press VCR ON/OFF (VCR POWER LED lights) to turn on the VCR, and press TV/ VCR to select the VCR (VCR LED lights).
3.Press MENU.